Manual Jablotron JA-60GSM (page 7 of 11) (English)

554884

Zoom out

Zoom in

1/11

JA-60GSM dialer module 7 / 11 MFJ51215

 If you are going to change the current SIM card in the dialer for

another one and the former one used a PIN code, enter

programming mode first and enter 70F0 (PIN code erasing in

the dialer).

5.2 GSM signal checking

If this function is enabled, the dialer will check regularly whether the

GSM signal is available. If it is not available for more than 15 minutes,

the system will indicate an external communication failure (failure L).

910 checking disabled

911 checking enabled

Default setting: checking disabled (910)

5.3 Reaction to an incoming call (remote access)

This sequence sets how the dialer will react to incoming calls. This

setting is important for remote access by telephone.

93 x

where

x = 0 no reaction to an incoming call

x = 1 to 8 will answer after 1=5sec., 2=10sec.,…,

8=40 seconds

x = 9 will answer after the second call = after the

ring is detected, there must be a pause

of 10 - 45 seconds. The dialer will answer

on the very first ring of the second call.

This setting can be used to bypass an

answering machine connected to the

phone output.

Default setting: 935 – the communicator will answer after 25 seconds

5.4 Remote access code setting

The following sequences are used for programming:

5.4.1 Service remote access code

94 xxxxxxxx F0

where

xxxxxxxx is the code, it can have 1 to 8 digits

If you enter 94F0 - the code will be erased and the remote access to

the alarm system will be not allowed.

Default setting: 0000 (4 zeros)

5.4.2 User remote access code

94 xxxxxxxx F1

where

xxxxxxxx is the code, it can have 1 to 8 digits

If you enter 94F1 - the code will be erased and user remote access to

the alarm system will be not allowed.

Default setting: 1111

5.5 Confirmation SMS reply messages

After the valid processing of an incoming SMS command, the dialer

automatically replies to the sender with a confirmation SMS message.

This confirmation is selectable:

950 automatic reply is disabled

951 automatic reply is enabled

Note: if the automatic reply is disabled, you can request a reply

manually by adding a space and the letter C after the last character of

the SMS instruction.

Default setting: 951 – automatic reply is enabled

5.6 Reset to default settings

Entering 96060 will cause the return to the default settings (all

telephone numbers will be erased and all unsent data will be erased.

For reloading the factory default SMS texts choose the language again

by the sequence 97701 (for English) or 9770x according to section

5.18.

5.7 Total reset – all communications disabled

Entering 96061 will erase all of the settings in the dialer’s memory and

the list of SMSes will be set to default setting.

5.8 One-time dialing-in during programming mode

While the control panel is in the programming mode, you can enable

one-time remote access by entering 970. After this code has been

entered, the dialer will respond to the first ring of any incoming call.

Without requesting the access code, it will enable the calling phone’s

keypad to be used as the keypad of the alarm system (= F, # = N).

This mode will be disabled after you dial-in, or after you exit

programming mode.

5.9 GSM signal monitoring

Enter 971 on the alarm system keypad (in programming mode) to

measure the GSM signal strength. The keypad will show a number

from 0 to 9 and it will sound a beep every second indicating a new

measurement each time. For proper functioning of the module the

signal strength should be 3 or higher. Find the best location for the

antenna while measuring the signal strength. To switch the system

back to programming mode press the N key.

Note: The standard antenna supplied with the JA-60GSM has a gain

of +3dB.

5.10 Attached phone function

The dialer provides a PHONE output to connect an ordinary

telephone set. The function of this telephone can be modified by

entering:

98 y

Where Function

y = 0 An ordinary telephone line is simulated, it is possible to

make phone calls (indicated with a dial tone in the

receiver)

1 If you pick up the receiver, the telephone keypad will work

as the keypad of the alarm system. It is impossible to

make phone calls in this mode (you will hear sounds of

the alarm keypad in the receiver)

y = 2 Disabled - the telephone has no function

y = 3 Emergency call – if you pick-up the phone, it will

automatically dial the emergency number (see 5.11)

Notes:

 If y=0 and you pick up the phone, the telephone keypad can be

switched to the alarm system keypad mode by pressing the #

key.

 If y=3 and you press the



key less than 2 seconds after you pick

up the phone, you will hear the dial tone and you can then call

any number. If the # key is used the same way, the keypad will

switch to the alarm system keypad mode.

Default setting: y = 0 ordinary telephone line is simulated

5.11 Setting the emergency call number

If the attached telephone is programmed for emergency calls (see

section 5.10), it dials the emergency number after you pick up the

receiver. This number can be entered by:

99 xx...x F0

where:

xxx…x is a telephone number (max. 20 digits), enter

F9 before the number if you need + prefix

for international calls

Default setting: no phone number is set (99F0)

5.12 Function of attached SMS-8010 phone

The communicator has a telephone connector, which can be used for

connection to a SMS-8010 phone. A detail description is in the

separate manual enclosed with the SMS-8010 phone. To use an SMS

phone enter code 001 instead of the telephone number (see chapter

3.1)

Setting:

 For sending SMSs to mobile phones it is necessary to set SMS

center 1 to “1111”..

 By sending SMSs to telephone number “001”, the central

panel can be controlled using SMS instructions

Note:

 Displaying the caller’s telephone number (CLIP): The

telephone number is shown in the international format

(00420212345678).

 If the phone call is made from a JA-60GSM a telephone

number of 001 and name of the caller “JA-60GSM“ will be

displayed.

Suddenly the system stopped and no communication with the main door panel Submitted on 24-9-2021 at 12:18
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-60GSM in the language / languages: English as an attachment in your email.

The manual is 0,19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-60GSM

Jablotron JA-60GSM User Manual - English - 6 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jablotron JA-60GSM Manual

Product: