Manual Jablotron JA-60GSM (page 8 of 11) (English)

554884

Zoom out

Zoom in

1/11

JA-60GSM dialer module 8 / 11 MFJ51215

5.13 Sustain calls for prepaid SIM cards

If a prepaid card is used, the dialer can automatically perform a sustain

call if there were no calls within a 3 month period. It will dial the

programmed number and after a 10 second call duration, the dialer will

hang up. The number, which should be called, can be entered by:

973 xxxxxxxx F0

where: xxxxxxx is the telephone number (max. 20 digits) – it is

recommended to call a time check service, weather reports etc.

5.14 Prepaid SIM cards

The JA-60GSM communicator can send information about the credit

balance of a prepaid SIM card. An SMS sent from any of the stored

numbers (sequence 7t...) containing the word CREDIT followed by the

correct command (different for every provider) will result in sending

information about the credit. Please ask your mobile phone provider for

more information.

CREDIT xxxxx where xxxxx is a string, which depends on the

GSM provider. Ask your provider for more

details

If you want to check the credit regularly use the following sequence.

CREDIT uuu..u xx yyy zz

where: uuu…u is the GSM-provider-defined instruction to be

transmitted to the provider for receiving information about the

amount of credit

xx is the time period (in days) between credit checks.

yyy is the minimum acceptable level of credit. A value

lower than this threshold triggers a warning SMS.

zz is an index or pointer, measured in characters from

the start of the provider message, showing the

position of the first digit of the credit value in the

information SMS sent by the provider. This allows the

GSM dialer to extract the credit value.

If the credit level is lower than the set value (yyy) the event “battery

discharged GSM communicator” will be sent to the preset telephone

numbers. If the credit is restored the event “battery OK GSM

communicator” will be sent to the preset telephone numbers. To

disable this function set the time (xx) period to 00.

Note:

 The user is responsible for the level of the credit

 The producer does not recommend the use of prepaid

cards.

When automatic credit checking is set to disabled, the user will be

unaware of expired credit. . Many GSM providers also demand regular

credit recharging. Therefore a prepaid SIM card is not recommended.

5.15 Telephone volume

The volume and sensitivity of the attached telephone can be adjusted

by:

974x receiver volume

975x microphone sensitivity

where x can be from 1 to 9 (factory default is 5 for both)

If the system is in programming mode, the volume can be adjusted

during a phone call.

5.16 GPRS communication setting

GPRS can be used for communication with a www server, for

connecting a PC to the internet or for communication with a CMS.

GPRS must be activated on the SIM card (for detailed information ask

your GSM provider). It is also necessary to set the APN in

programming mode in the communicator using ComLink software.

5.17 GSM module reset

Enter 976 to disconnect and connect the GSM module to the GSM

network. This function is useful when it is necessary to switch the

mobile device off and on (e.g. when the SIM card has been unblocked

by the mobile operator).

It is also possible to send the command via SMS in the form yyyyy*GSM,

where yyyyy is service access code. The command is processed

independent of the state of the system.

5.18 Language setting

Language of the text used by the communicator can be set by

instruction:

977 xx

where:

xx is number of the language – see the following list:

01 EN English 09 PL Polish

02 CZ Czech 10 PT Portuguese

03 SK Slovak 11 RU Russian

04 DA Danish 12 SE Swedish

05 FI Finnish 13 TR Turkish

06 DE German 14 ES Spanish

07 HU Hungarian 15 NL Dutch

08 IT Italian 16 CN Chinese

Note:

 Set the language before editing the text in the system (change of

the language will change the text to the factory default).

 Set language will not be changed when reset is performed.

 Language setting can NOT be performed via the ComLink

software or the GSMLink.

 This feature is only available for communicators equipped with

SW version FJ61412 or higher.

 Do not use *.jag files for language setting.

Example: by setting 97702 the Czech language will be set.

Factory default : 97701 = English

6 Web server remote access

6.1 System programming

The GSMLink server allows a user/installer to read and change the

control panel and dialer configurations. Data transfer is achieved by

sending an SMS or GRPS data. The web site allows the following

programming:

 control panel settings

 dialer settings

 editing of SMS reports

 monitoring station settings

The web site is also able to read the event memory of the control

panel. The amount of data sent by SMS is optimized to minimize costs.

Alternatively GPRS data transfer can be used, but this must be

activated on the SIM card.

6.2 Web site registration

System registration can be performed in two ways:

The www.gsmlink.cz website

– to register your system use the

registration code printed on the warranty certificate (the code has a

form xxxx-xxxxx-xxxx and it is a unique for each system). The dashes

(-) must be included when registering.

By mobile phone – when the alarm system is in programming mode,

enter 972 xxxx F0 on the alarm system keypad (xxxxx is your mobile

phone number). After a moment you will receive an SMS with the

registration code and the system will register on the web server.

7 Central Monitoring Station communication settings

The dialer can report events to two different Central Monitoring

Stations (CMS). Each CMS has its own setting sequences that differ in

parameter p (p=1 for CMS1 and p=2 for CMS2). The dialer uses

Ademco Contact ID format and it is also equipped for the future use of

GPRS data transfers. The product is able to report events to a CMS

based on either landline or GSM data transfer.

7.1 CMS phone number entry

Primary and back up telephone numbers can be entered for each CMS:

Primary number: 01 p xx....x F0

Back up number:

02 p xx....x F0

where:

xxx...x is a telephone number, max. 20 digits

p 1=CMS1, 2=CMS2

Example: 123456789 can be entered as the CMS2 primary number by

entering: 01 2 123456789 F0

Suddenly the system stopped and no communication with the main door panel Submitted on 24-9-2021 at 12:18
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-60GSM in the language / languages: English as an attachment in your email.

The manual is 0,19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-60GSM

Jablotron JA-60GSM User Manual - English - 6 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jablotron JA-60GSM Manual

Product: