Manual Jablotron JA-60GSM (page 1 of 11) (English)

554884

Zoom out

Zoom in

1/11

JA-60GSM dialer module 1 / 11 MFJ51215

JA-60GSM dialer module

Installation manual

The JA-60GSM dialer is constructed for the JA-60, 63 and 65 alarm control panels. The dialer is used for communication via GSM. An

appropriate GSM provider is chosen according to the inserted SIM card. This Installation manual is intended for the JA-60GSM, version FJ61412.

The GSM module, when installed in the alarm control panel, enables:

 Automatic sending of an event’s text messages to up to 8 mobile phones

 Dialing of programmed telephone numbers and playing of an audible warning signal

 Data transfer to one or two Central Monitoring Stations (CMS)

 Remote control and programming of the alarm system via SMS instruction messages from a mobile phone or from Jablotron’s SMS

website

 Remote control and programming of the alarm system using a telephone set keypad (mobile or land line)

 Remote control of an appliance (heating system etc.) via telephone (mobile or land line)

 Phone calls and convenient receiving and sending of SMS messages using an SMS-8010 telephone set (optional accessories; except

GSM kits e.g. JK-05) attached to the dialer module (via the GSM network)

 Connection of the intercom SP-01 for communication with the premises

 Internet connection using the GPRS data transfer

 Programming of the alarm system via ComLink software

 Programming and remote supervision of the alarm system via Jablotron’s website www.gsmlink.cz

 Multi-language support (only available via keypad instructions)

1 Installation of the dialer

The JA-60GSM dialer can be installed into the telephone

communicator’s position in a JA-60, 63 or 65 control panel (either a

GSM module or a telephone line communicator module can be used in

a control panel – it is not possible to install both simultaneously).

a) Disconnect the control panel’s power supply (both AC and

backup battery). If the control panel has been previously used

before this installation, enter the programming mode before

disconnecting the power supply.

b) We recommend you to disable the SIM card PIN code

protection before you insert it into the dialer. Use a mobile phone

to perform this task (if you have a NOKIA phone, select: Menu,

Settings, Security settings, PIN code request, Off). If you insist on

usage of the PIN, see section 5.1.

c) Open the SIM card holder (by sliding it in the direction shown in

figure 1) and Insert the SIM card into the holder and close it by

sliding it back. – see figure 1.

d) Attach the dialer into the control panel case and connect its flat

cable to the control panel’s main board.

e) Connect the GSM antenna (never switch the power supply on

without a proper antenna)

f) Connect a SMS-8010 telephone set to the PHONE connector (or to

PHONE terminals) if desired. Only one telephone set can be attached

to the dialer. The PHONE output of the dialer should never be

connected to any other telephone network.

g) If you use the AUX output to control an appliance, connect its

cable to the AUX output terminals (normally open dry contact,

max. 100mA / 60V) – see figure 1.

SPAC E

CANCEL MENU NAMES CALLS WRITE READ



SMS

CALL

MUTE

FLASH

REDIAL

SPEA KE R

figure 1

Note: if your control panel supports programming of the PgX and

PgY outputs for the AUX function (sequences 238 and 239), the

appliance can also be controlled wirelessly from the control panel

by incorporating a UC-216 or UC-222 receiver module into the

system.

h) Reconnect the control panel’s power supply (backup battery

and AC). The system will show a P, (programming mode). The red

LED on the GSM dialer will light permanently (indicating that the

module is establishing a connection with the GSM network). The

LED will switch off after the connection is successfully

established.

If the LED starts flashing, the module was not able to connect to

the GSM network. In this case, switch off the control panel’s power

completely. Remove the SIM card and insert it into a mobile phone

to confirm whether it is possible to connect to the network at this

location. You can also select a desired network manually if options

are available. Ensure that the SIM card does not request a PIN

code (optional use with a PIN code is described in section 5.1).

Once the SIM card works in the mobile phone, reinsert it into the

GSM dialer and repeat step h). If the GSM signal is weak in this

area, change the location of the GSM antenna before you try to

reestablish the connection.

i) Attach the control panel’s cover after the module has connected to

the GSM network (LED switched off).

j) Key in 97701 - to set texts of the communicator to English

language. (English is the default setting, so you can omit this step.)

k) Enter 971 on the alarm system keypad (while in programming

mode) to monitor the GSM signal. The keypad will show a

number from 0 to 9 and it will sound a beep every second

indicating a new measurement. For proper functioning of the dialer

the signal strength should be 3 or higher. Find the best location for

the antenna while measuring the signal strength. To switch the

system back to programming mode press the N key.

l) Without additional programming you can test the user features of

the dialer (phone calls from an attached phone, remote control of

the system via a remote phone, remote control of an appliance

etc.). See the following description.

m) Set telephone numbers for automatic event reporting and the

other selectable features – see part 3.

n) Programming of the GSM dialer is possible by entering

programming sequences via the alarm system’s keypad (while in

programming mode). The most convenient programming method,

however is via a connected PC using ComLink software, or by

using the www.GSMlink.cz

website.

Suddenly the system stopped and no communication with the main door panel Submitted on 24-9-2021 at 12:18
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-60GSM in the language / languages: English as an attachment in your email.

The manual is 0,19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-60GSM

Jablotron JA-60GSM User Manual - English - 6 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jablotron JA-60GSM Manual

Product: