Manual Jablotron JA-60GSM (page 3 of 11) (English)

554884

Zoom out

Zoom in

1/11

JA-60GSM dialer module 3 / 11 MFJ51215

2.10 Alarm system remote control from a telephone keypad

If you want to operate the alarm system from a phone (mobile or

landline), perform the following:

a) Dial the alarm system phone number. The attached telephone

will ring

b) If the phone is not answered, the system will answer after 25

seconds - indicated by a short beep

c) Enter the remote access code; factory default is 0000 (4 zeros);

to change this code see section 5.4

d) Confirmation sounds indicate the control panel mode: 1 beep =

armed, 2 beeps = disarmed, 3 beeps = programming mode,

Siren sound = alarm.

e) From this moment the telephone keypad will work as the alarm

control panel keypad. The

* Key is interpreted as F, the # key

as N.

f) Confirmation sounds indicate the control panel mode: 1 beep =

armed, 2 beeps = disarmed, 3 beeps = programming mode,

Siren sound = alarm.

g) To terminate the connection simply hang up. The connection will

also be terminated if there is no entry within 60 seconds.

Notes:

 Remote access from a landline is only possible from a phone

using tone dialing (DTMF)

 The reaction of the alarm system to incoming calls can be

modified: see section 5.3

 It is impossible to operate the system remotely without a valid

remote access code (if used).

2.11 Appliance remote control via a telephone keypad

If you want to operate outputs PgX or PgY (e.g. a household

appliance) from a phone (mobile or landline), perform the following:

a) Dial the alarm system number. The attached telephone will ring.

b) If the phone is not answered, the system will answer after 25

seconds - indicated with a short beep.

c) Enter the remote user access code; factory default setting is 1111 ;

to change this code see 5.4.

d) The system will confirm validity of the code with a beep.

e) From this moment you can operate the PgX and PgY outputs (if

they are each predefined as phone-controllable) by entering:

*80 to switch off PgX or PgY, or both together,

*81 to switch on PgX or PgY, or both together

(continuously).

f) To terminate the connection simply hang up. The connection will

also be terminated if there is no entry within 60 seconds.

Notes:

 Remote access from a land line is only possible from a phone

using tone dialing (DTMF)

 The reaction of the system to incoming calls can be modified: see

section 5.3

 If the system is not allowed to control without code, the control

sequence must be complete with a user code:

*8[user code]1

*8[user code]0

 For this function it is necessary that the alarm system supports F

81 and F 80 sequences

 If the dial in function is set (see 3.1.) it is possible to switch ON

the PgX or PgY output for two seconds. The phone call is not

answered therefore it is free of charge.

2.12 Remote voice communication with premises

If the SP-01 intercom is plug-in to the PHONE terminal (it must not be

combined with any phone connected) it is possible to create a one way

(talking or listening) communication from an authorized (stored) phone

numbers (see. 3.1). Procedure:

a) From an authorized phone dial the JA-60GSM phone number.

The SP-01 will ring once and then it will answer the call

b) Potential alarm on the control panel will be terminated

c) You can talk to the premises

d) For switching to the listening mode press 5 on your phone.

For switching back to the talking mode press key 2. Or by

pressing button 1 it is possible to toggle between talking and

listening.

e) Press 0 or hang-up to terminate the call.

Note:

 Only a phone with available DTMF can be used.

3 SMS and audible alarm reports

The factory default settings allow the GSM dialer to send SMS

reports and audible warnings when the control panel generates

important information (alarms, arming, etc.). It is only necessary to set

the telephone numbers which the information should be reported to. To

enter these numbers, first enter programming mode.

If you prefer to report more or different events than the factory

default provides, see section 4.

3.1 Telephone numbers entering

The dialer has 8 telephone number memories. Each memory has

assigned particular SMS reports and/or audible warnings according to the

default setting – see table 1.1. By entering a telephone number in to a

particular memory location you are selecting what will be reported to this

number:

7t xxx...x F0

Where t is a memory location from 1 to 8

xxx...x is a telephone number (max. 20 digits),

enter F9 before the number, if you need the + prefix for international

calls. To use an attached SMS telephone set, enter code 001 instead of

the telephone number. To authorize a phone number for communication

with premises via the SP-01 intercom set F8 (#) at the end of the phone

number or F7 (*) for dial-in function (see 2.11.).

To disable reporting to a particular number, delete this number

memory by entering:

7tF0

where t is a memory from 1 to 8

Report testing:

If you wish to report any alarm, arming and disarming by SMS followed

by the notifying call and your mobile phone number is 123456789, then

enter 75123456789F0 (while the control panel is in programming mode).

Then exit programming mode by pushing the N key. Now you can arm

the system and your mobile phone will receive a reporting SMS.

3.2 Installation name in SMS reports

Each reporting SMS message starts with: “Alarm system reports:”. You

can change this default title text by sending the dialer the following text

programming SMS:

yyyyyTXT700,text

where

yyyyy is the remote access code; factory default is 0000 (4

zeros); the code can be changed, see 5.4

TXT is the text programming command

700 is the index number on the system text table

corresponding to the installation name

, comma (separator)

text is your own new installation name. A comma or dot

cannot be used in the text. A blank space inside the

text is a valid character (the dialer ignores spaces

before the separator)

 separating character, which can be replaced by a space

Example: If the default code is in the dialer, then sending SMS:

0000 TXT 700, Mr. Diamond’s jewelry shop reports:

to the dialer will change the installation name to the above text.

Note: all the SMS texts stored in the dialer can be changed in a similar

way, see section 4.2 for details.

Suddenly the system stopped and no communication with the main door panel Submitted on 24-9-2021 at 12:18
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-60GSM in the language / languages: English as an attachment in your email.

The manual is 0,19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-60GSM

Jablotron JA-60GSM User Manual - English - 6 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jablotron JA-60GSM Manual

Product: