554884
4
Zoom out
Zoom in
Previous page
1/11
Next page
JA-60GSM dialer module 4 / 11 MFJ51215
3.3 Telephone number table
4 Customization of SMSs and audible reports
The default text and audible reports sent can be modified.
The dialer can report all possible events of the alarm system by SMS
(see table 4.1.1).
It is possible to set which events will be reported to which telephone
number.
There are factory default SMS texts available for all possible events and
for all possible event sources. All these texts can be edited.
It is possible to set which events should activate audible warnings.
The communicator can report all possible events by dialing programmed
numbers and playing an audible warning - if the call is answered
It is possible to change SMS command texts, which are used for remote
control of the system.
First enter the programming mode if you are going to use the following
programming sequences:
4.1 Events to be reported by SMS
Table 4.1.1 shows the complete list of all possible events in the alarm
system together with each corresponding index number. It also shows
which events are assigned to which telephone numbers to be reported
by SMS. You can make your own setting by using:
81 uu t y
where
uu is the event index from 01 to 31 (see table 4.1.1)
t is a telephone number memory location from 1 to 8
y 0 = reporting disabled, 1 = reporting enabled
Note: SMS reports consist of 4 text parts (installation name, event
name, event source name and time) – all of these texts can be edited
and customized, see section 4.2 for details. In a single SMS there can
be up to 160 characters using ASCI format, or 65 characters using
UNICODE format. Exceeding these limits will result in split messages.
The event “Internal communication failure” is generated if any of the
wireless detectors are lost under RF supervision.
The event “External communication failure” is generated if there is a
GSM signal outage longer than 15 minutes. The release of this event
is possible when GSM signal monitoring is set to ON.
Example: if you enter 810381 and a Fire alarm is triggered (event
index 03) by detector number 1, the following message will be sent to
the 8
th
telephone number: “Alarm system reports: Fire alarm Wireless
detector #1 Time: 16.04. 11:16”
4.1.1 Table – SMS report assignments to telephone numbers
Telephone numbers Event index
uu
Event
1 2 3 4 5 6 7 8
01 Intruder alarm instant zone x x x x x x
02 Intruder alarm delayed zone x x x x x x
03 Fire alarm x x x x x x
04 Panic alarm x x x x x x
05 Wrong access code alarm x x x x x x
06 Alarm after power on x x x x x x
07 Tamper alarm x x x x x x
08 Tamper OK
09 Alarm end
10 Alarm canceled by a user x x x x x x
11 Arming
x x
12 Disarming
x x
13 Partial arming (Home) x x
14 No code arming x x
15 External communication failure x x x x x x x
16 External communication recovery
17 Failure x x x x x x x
18 Failure recovery
19 AC failure longer than 30 minutes x x x x x x x
20 AC failure
21 AC recovery
22 Battery failure x x x x x x x
23 Battery recovery
24 Enter programming mode
25 Exit programming mode
26 Remote access
27 Remote access end
28 RF jamming
29 Internal communication failure x x x x x x x
30 Internal communication recovery x x x x x x x
31 Periodic test
The x marks in the table show which events are assigned to which telephone numbers for SMS reporting. If you modify these, we recommend you to
mark your settings in the table.
Memory
Entry
sequence
Reporting mode for the two corresponding phone numbers: Notes
1 71 ______ F0
2 72 ______ F0
- ALARM SMS if there is any type of alarm in the system (intruder, fire, tamper, panic).
- Technical SMS about events in the system.
3 73 ______ F0
4 74 ______ F0
- ALARM SMS if there is any type of alarm
- ALARM CALL notifies the called person (if you answer such a call, you will hear an
audible warning).
- Technical SMS about events in the system.
5 75 ______ F0
6 76 ______ F0
- ALARM, ARMING & DISARMING SMS.
- ALARM CALL notifies the called person (if you answer such a call, you will hear an
audible warning).
- Technical SMS about events in the system.
7 77 ______ F0
8 78 ______ F0
- ALARM CALL notifies the called person (if you answer such a call, you will hear an
audible warning). This setting is suitable for notifying landline numbers. -
Technical SMS about events in the system. This position is reserved only for the
service/installer organization.
Only numbers, which can accept
SMS, should be entered for the SMS
reports (mobile phones, provider’s
call centers etc.)
Audible warnings can be sent both to
mobiles and to landlines too
The communicator can report all
possible events from the alarm
system, not only the events listed in
the table above. See section 4 for
details.
4


Need help? Post your question in this forum.

Forumrules
1

Forum

jablotron-ja-60gsm

Reset search

  • Suddenly the system stopped and no communication with the main door panel Submitted on 24-9-2021 at 12:18

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-60GSM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-60GSM in the language / languages: English as an attachment in your email.

The manual is 0,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-60GSM

Jablotron JA-60GSM User Manual - English - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info