554884

Jablotron JA-60GSM Manual

9
Zoom out
Zoom in
Previous page
1/11
Next page
JA-60GSM dialer module 9 / 11 MFJ51215
Note: The IP address can be set a similar way. For example the IP
address 192.168.1.123 on port 08080 can be set by entering 01 2 F8
129 168 001 123 8080, where F8 (#) introduces the IP address, which
must always have 12 numbers, and the port 5 numbers
.
CMS phone number erasure is possible by entering 01pF0 or 02pF0.
There will be no data transfer to a CMS if its numbers are erased.
Default setting: No phone number set
7.2 Account ID setting
A CMS uses this ID number for alarm system identification:
03 p zzzz F0
where:
zzzz is the account ID number (z = numbers from 0 to 9 or
A=F1, B=F2, C=F3, D=F4, E=F5 a F=F6)
p 1=CMS1, 2=CMS2
Default setting: ID is 0000 for both CMSs
7.3 Format setting
This sequence is used to select the communication format:
04 p x
where:
p 1=CMS1, 2=CMS2
x protocol type – see table
Protocol Type x
Contact ID DTMF 0
Jablotron SMS SMS type
1
Jablotron GPRS GPRS type
2
Default setting: Contact ID for both CMSs
7.4 Events to be reported to CMS
There are 31 types of events, which can be reported to each CMS –
see table 7.4.1. This sequence sets which events should be reported
to CMSs.
05 p uu y
where
p 1 = CMS1, 2 = CMS2
uu events index – see table 7.4.1
y 0 = report disabled, 1 = report enabled
Default setting: all reports are disabled
7.4.1 Table – complete list of events to be reported to CSM
Events index uu Events description
01 Intruder alarm – instant zone
02 Intruder alarm – delayed zone
03 Fire alarm
04 Panic alarm
05 Wrong access code alarm
06 Alarm after power on
07 Tamper alarm
08 Tamper OK
09 Alarm end
10 Alarm canceled by a user
11 Arming
12 Disarming
13 Partial arming (Home)
14 No code arming
15 External communication failure
16 External communication recovery
17 Failure
18 Failure recovery
19 AC failure longer than 30 minutes
20 AC failure
21 AC recovery
22 Battery failure
23 Battery recovery
24 Enter programming mode
25 Exit programming mode
26 Remote access
27 Remote access – end
28 RF jamming
29 Internal communication failure
30 Internal communication recovery
31 Periodic test
7.5 CMS re-dialing pause setting
If the dialer is activated it attempts to make a connection (alternating
between the primary and the backup telephone number). If it is not
possible to make a connection, a pause is initiated. After this pause
the dialer will attempt again. The pause length can be set in the
following way:
06 p t
where
t pause duration x 5 minutes (1 = 5 minutes, 2 = 10
min,..., 9 = 45 minutes)
p 1 = CMS1, 2 = CMS2
Default setting: 5 minutes for both CMSs
7.6 Interval of periodic test
The periodic test for checking the CMS link is set by activating event
No 31. The following sequence sets the time length from the last
reported event to the moment when the periodic test report should be
transferred.
07 p hhmm
where
p 1 = CMS1, 2 = CMS2
hh hours
mm minutes
Default setting: The periodic test report is sent 24 hours after the last
reported event.
7.7 Disabling CMS communication
If you need to disable all CMS reports temporarily, you can do this,
while retaining your settings:
0 0 p 0 all reports to CMS p disabled
0 0 p 1 all reports to CMS p enabled
Default setting: all CMS reports disabled.
7.8 CMS 2 as a back up for CMS1
CMS 2 can serve as an optional back-up for CMS if data transfer to
CMS1 fails. When the first event is transferred to the backup
monitoring station (CMS2) an event “tel. line #1 communication fault“
will be reported.
080 CMS1 and CMS2 are two independent stations
081 CMS 2 works as a back up for CMS 1.
When 081 is selected, CMS 2’s settings are used only in the case of
CMS 1 transfer failure.
Default setting: two independent CMSs.
7.9 Storing the event “data to CMS sent” into the event memory
By this sequence it is possible to disable recording of the event that
indicates that data to a CMS has been sent to the list of event in the
control panel.
Programming sequences:
090 The CMS data transfer event is not recorded
091 The CMS data transfer event is recorded
Default setting: The CMS data transfer event is recorded
8 The modem function
The GSM communicator can also be used as an external modem for
accessing the Internet (GPRS format). It is necessary to have GPRS
activated in the SIM card and to have a connection cable connected to the
COM port of the PC. Support for MS Windows operating systems can be
found on the enclosed CD. The modem can only be used when all CMS
reports, SMSs and system calls have been executed.
When the modem is used:
It is possible to use the attached telephone, the internet connection will
be temporally suspended
Received SMSs are stored and they will be processed after modem
disconnection
The modem will be disconnected if an alarm or an arming event occurs
9 Additional information
9.1 Priorities for event reporting:
If the dialer is activated to send an event report it will:
send information to CMS1 (trying primary and back up
numbers twice) if programmed
… 9


Need help? Post your question in this forum.

Forumrules
1

Forum

jablotron-ja-60gsm

Reset search

  • Suddenly the system stopped and no communication with the main door panel Submitted on 24-9-2021 at 12:18

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-60GSM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-60GSM in the language / languages: English as an attachment in your email.

The manual is 0,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-60GSM

Jablotron JA-60GSM User Manual - English - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info