Manual Scheppach DP60 (page 28 of 100) (English, German, Dutch, French, Italian, Portuguese, Spanish)

781653

Zoom out

Zoom in

1/100

www.scheppach.com

28 | GB

8.7 Fastening to a work surface (g. 6)

Fasten the device to the work surface by bolting the

base plate (1) to the work surface.

The table mounting attachment kit (E) can be used for

this.

9. Operation

9.1 Operation of the display (g. 7)

• Switching the display on/off:

Press the button (I, 2-3 sec.) until the display (9)

switches on or off.

• Display of drilling depth/speed:

The display can be switched between displaying the

speed and the drilling depth by pressing button (F).

• Setting the zero point:

The zero point for the drilling depth can be set by

pressing the button (G).

• Switching the laser cross on/off:

The laser cross can be switched on or off by press-

ing the button (H).

• Switching the LED on/off:

The LED work light can be switched on or off by

pressing the button (I).

9.2 Height adjustment (g. 1):

The position of the machine head can be adjusted to

suit the workpiece height or the workpiece length.

1. Hold the handle (8) rmly.

2. Release the clamping lever for the height adjust-

ment (5).

3. Set the position of the machine head with the han-

dle (8).

4. Secure the position of the machine head with the

clamping lever for height adjustment (5).

m Attention!

Ensure in the lowest machine head position that the

machine head will not be moved beyond the marking.

Use the clamping lever for height adjustment (5) to se-

cure the machine head in this position. Otherwise, the

guide could be damaged.

9.3 Setting the drilling depth (g. 1)

The drilling depth can be set with the depth stop (7).

1. Release the clamping lever on the depth stop (6).

2. Carry out a test drilling. As soon as the desired

depth is shown on the display (9) (refer to point

9.9 also), tighten the depth stop clamping lever (6)

again.

3. Tighten the pre-assembled fastening screws (A)

on the rear of the base plate (1) with the Allen key

(19).

8.2 Fitting the parallel stop (g. 2)

1. Slide the parallel stop (16) into the grooves in the

base plate (1).

2. Ensure that the sliding blocks underneath the wing

screws of the parallel stop (15) are properly en-

gaged in the grooves of the base plate.

3. Move the parallel stop (16) to the desired position

and tighten the wing screws of the parallel stop

(15) rmly.

8.3 Assembling the chuck guard (g. 3)

1. Insert the chuck guard (13) into the holes provided

in the machine frame.

2. Secure the chuck guard (13) by hand-tightening

the screws (C).

8.4 Assembling the handle (g. 4)

The handle (8) can be mounted on the right-side of the

machine for right-handers and on the left-side of the

machine for left-handers.

When installing the handle (8), ensure that the availa-

ble mating surfaces engage.

1. Slide the mounting mandrel (8.1) onto the handle

(8).

2. Fit the spacer sleeve (8.2) to the mounting mandrel

(8.1).

3. Fit the handle (8) with the mounted mounting man-

drel (8.1) and the spacer sleeve (8.2) to the retain-

er (D).

4. Fasten the handle (8) using the Philips screw (B).

5. Attach the handle cover (8.3) to the handle (8).

To disassemble the handle (8), remove the handle cov-

er (8.3).

Now remove the handle (8) in reverse order.

8.5 Assembling the depth stop (g. 5)

Insert the depth stop (7) into the hole provided in the

housing.

8.6 Assembling the clamping lever for depth stop

(g. 5)

Assemble the clamping lever for depth stop (6) as

shown in g. 5.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach DP60 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 5,22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach DP60 Manual

Product: