Categories
781653

Scheppach DP60 Manual

30
Zoom out
Zoom in
Previous page
1/100
Next page
www.scheppach.com
30 | GB
General maintenance tasks
Wipe swarf and dust off the machine from time to time
with a cloth. Oil the rotating parts once monthly to ex-
tend the life of the tool. Do not oil the motor.
Do not use corrosive agents for cleaning the plastic.
m Have tasks that are not described in this operat-
ing manual, carried out by a specialist workshop.
Use only original parts. Let the device cool down
before all maintenance and cleaning tasks.
m There is a risk of burn!
Before using the device each time, check the device
for obvious defects such as worn or damaged parts,
correct seating of screws or other parts. Replace dam-
aged parts.
Cleaning
Do not use cleaning agents or solvents. Chemical sub-
stances could damage the plastic parts of the device.
Never clean the device under running water.
• Clean the device thoroughly after each use.
• Clean the ventilation holes and the surface of the
device with a soft brush or cloth.
• Remove swarf, dust and dirt with a vacuum cleaner
if necessary.
• Lubricate the moving parts regularly.
Maintenance
The device has no parts that require maintenance.
Replacing the chuck (g. 10)
m Warning! Pull out the mains plug!
Tools required:
1x open-ended spanner (at) 16 mm
1x Allen key 2.5 mm (not included in the scope of de-
livery)
• Loosen the Allen screw by turning it counter-clock-
wise ca. 2 turns.
• Hold the chuck shaft in place with the spanner (20)
and unscrew the chuck counter-clockwise with your
free hand.
• Fasten the new chuck in reverse order.
When replacing the chuck, use only chucks approved
by the manufacturer.
Order number: 390 6813 010
9.9 Displaying the drilling depth (g. 1/7)
1. Set the display (9) to the “Drilling depth” indication
(button F).
2. Set the tip of the drill bit down lightly on the work-
piece.
3. Set the zero point by pressing the button (G).
4. Drill until the desired depth is shown on the dis-
play (9).
9.10 Switching on/off (g. 1)
m Make sure that the chuck guard (13) is folded
down before switching on.
Switching on:
Press the on switch (11) to switch the device on.
Switching off:
Press the off switch (10) to switch the device off.
9.11 Drilling procedure (g. 1)
1. Align the workpiece and clamp it.
2. Start the device and set the speed.
3. For drilling, move the handle (8) with uniform feed
until the desired drilling depth is reached. When
drilling into metal, interrupt the downward pressure
briey to break the swarf.
4. After reaching the drilling depth, return the handle
(8) to the starting position.
5. Switch the device off.
10. Transport
• To transport the device hold it by the base plate (1).
11. Cleaning and maintenance
m Warning!
Pull out the mains plug before carrying out any adjust-
ments, maintenance or repair work!
… 30 …

Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach DP60 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach DP60 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 5,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info