Categories
781653

Scheppach DP60 Manual

29
Zoom out
Zoom in
Previous page
1/100
Next page
www.scheppach.com GB | 29
9.7 Clamping larger workpieces (g. 9)
Use the parallel stop (16) for larger workpieces:
1. Loosen the wing screws for the parallel stop (15)
and insert the parallel stop (16) into the grooves of
the base plate.
2. Tighten the wing screws for the parallel stop (15).
3. Align your workpiece against the parallel stop (16)
and clamp it with the quick clamp (2).
m Warning!
With workpieces that are wider or longer than the tab-
letop, ensure that these are adequately supported, e. g.
through trestles or saw horses.
Workpieces that are longer or wider than the base
plate of the tabletop drill can tip if they are not properly
supported. If the workpiece tips, this can damage the
chuck guard or the cutting tool.
9.8 Setting the drilling speed (g. 1)
The correct speed must be set to suit the workpiece to
be drilled and the tool diameter.
Mechanical gear selection:
Two different speed ranges can be selected with the
gear selector switch (18).
Gear 1:
Low speeds (170- 880 min-1) for large tool diameters.
Gear 2:
High speeds (490-2600 min-1) for small tool diameters.
m Attention:
Actuate the gear selector switch (18) only when at a
standstill. If the gear selector switch (18) does not latch
into place turn the chuck (14) a little.
If the gear selector switch (18) cannot be turned as far
as the stop, turn the chuck a little with the drill.
Electronic speed control:
The speed of the individual gears can be seamlessly
adjusted with the electronic speed control:
Set the speed with the help of the speed control (12).
The current speed can be seen on the display (9).
3. The depth stop (7) is now locked in the desired
drilling depth.
9.4 Clamping/releasing drill bits (g. 8)
Clamping:
1. Hold the chuck in place and turn the securing ring
(K) in the “RELEASE” direction.
2. Turn the clamping sleeve (L) clockwise until the
drill bit can be inserted. Hold the holding ring (J) in
place whilst doing so.
3. Insert the drill bit, hold it in place and turn the
clamping sleeve (L) counter-clockwise by hand.
Hold the holding ring (J) in place whilst doing so.
4. Hold the chuck in place and turn the securing ring
(K) in the “LOCK” direction.
Note:
When using small drill bits, set the chuck to roughly the
right size for the drill bit beforehand. Otherwise there
is a risk of the drill bit not being properly centred in the
chuck.
Releasing:
1. Turn the securing ring (K) in the “RELEASE” di-
rection.
2. Turn the clamping sleeve (L) clockwise until the
drill bit can be removed.
9.5 Aligning workpieces
1. Switch on the laser cross via the display (9). See
9.1, Operation of the display.
2. The intersection of the two laser lines exactly indi-
cates the centre point of the drill.
3. Align your marking on the workpiece with the laser
cross.
9.6 Clamping the workpiece (g. 9)
It must be possible to clamp the workpiece securely.
Do not work with workpieces that cannot be clamped
securely.
The cut-out of the quick clamp must be centrally
aligned with the hole to be drilled. Otherwise, the drill
bit or the chuck could be obstructed by the quick clamp.
1. Position the workpiece with the help of the laser
cross.
2. Loosen the quick clamping lever (17).
3. Place the quick clamp (2) on the workpiece.
4. Turn the quick clamp lever (17) clockwise to clamp
the workpiece.
5. Turn the quick clamp lever (17) counter-clockwise
to release the quick clamp (2).
… 29 …

Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach DP60 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach DP60 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 5,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info