479878
6
Zoom out
Zoom in
Previous page
1/8
Next page
10.0 - SSELF-LEARNING OF TURN INDICATORS FLASHE
In order to arm/disarm through the turn indicators, the system must learn the vehicle
locking(arming)/unlocking (disarming) signals.
To do so, connect the WHITE-ORANGE wire to the turn indicators and then proceed as follows:
Disconnect the 8-way wiring connector from the 8-way system connector.
Turn ignition key “ON”.
Connect the 8-way wiring connector to the 8-way system connector; the LED will turn on.
urn ignition key
Close any open door and press the lock button on the original remote control.
Once the turn indicators stop flashing, the system will emit 1 high-pitched audio signal indicating
the arming flashes have been memorized.
Press the unlock button on the original remote control.
Once the turn indicators stop flashing, the system will emit 2 high-pitched audio signals indicating
the disarming flashes have been memorized.
This completes the procedure.
!
!
!
!
!
!
!
!
! T “OFF”.
12.0 - SYSTEM PROGRAMMING
The t
E
able below applies to the system programmed in “standard configuration”.
ntering the programming procedure resets the functions to the default setting.
Visual signals activated by a connection to the hazard button, will ONLY turn on during
an alarm situation.
The system BLU wire MUST be connected to the hazard button.
The system ORANGE wires MUST NOT be connected to the turn indicators (see
chapter 8.3).
!
Alack of power during electrical system maintenance, will not affect the programming.
The procedure must be carried out completely because functions are disabled by changing the
position of the ignition key, which then activates the next step up to completion of the programming
procedure.
The next paragraph illustrates the programming instructions.
Programmable functions are briefly described below.
This function activates visual signals during system arming (1) and disarming (2).
12.1 - OPTICAL SIGNALLING
The turn indicators alarm signals should be disactivated if visual signals are present
when locking/unlocking the vehicle.
12.2 - ACOUSCTIC SIGNALLING
12.3 - PASSIVE ARMING
12.4 - 5)
12.5 - BOOT PUSH-BUTTON POLARITY SELECTION
12.6 - IMPULSE VISUAL SIGNALLING SELECTION
This function activates audio signals during system arming (1) and disarming (2).
(art. 7725).
This function modifies the alarm input signal (positive or negative) according to the signal
This function activates the
This function arms the system 60” after switching off ignition and opening and closing the last door.
Opening a door during this operation interrupts the procedure which will resume when door is closed.
sent by the
boot push-button.
visual signalling according to the connection; it must be activated only
when connections are made directly on the wire deriving from the hazard button (not availablbe for all
vehicles).
ARMING OF SIREN (ART. 772 OUTPUT
This function arms the relative output (20-way connector, position 13, PINK wire) to activate the self-
powered coded siren
!
FUNCTION STATUS
Disabled
Enabled
Disabled
Disabled
Disabled
Disabled
Disabled
Exclusion of arming/disarmin optic signalling
Exclusion of arming/disarmin acoustic signalling
System passive arming
Arming of self-powered coded siren
Positive signal trunk input
Impulse visual signalling
Negative output during alarm phase
INSTALLER MANUAL - PAGE 11PAGE 10 - INSTALLER MANUAL
To cancel the programming of the turn indicators reset the system (see
chapter 15.0).
!
11.0 - DIP-SWITCHES PROGRAMMING TABLE
Set dip-switches BEFORE connecting the alarm system.
If settings must be modified after installation, FIRST disconnect alarm and then reset
dip-switches.
With dip-switch nr. 2 “ON”, YELLOW-RED wire is grounded when system is armed.
With the vehicle closed, leave dip-switch in this position when connecting only the
WHITE/LIGHT BLUE wire to the lock switch (connected to ground).
!
!
Nr. POSITION FUNCTION
ON
OFF
ON
OFF
ON
OFF
ON
OFF
POSITIVE polarity for control on WHITE/LIGHT BLUE wire
NEGATIVE polarity for control on WHITE/LIGHT BLUE wire
Positive signal (+A) on BROWN/RED with alarm on
Normal functionning
Negative commands - arming/disarming system
Positive commands - arming/disarming system
System arming with door locking motor unit or with door locking motor unit
and turn indicators (see par. 9.0)
System arming with turn indicators only
1
1
2
2
3
3
4
4
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 821 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 821 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gemini 821

Gemini 821 User Manual - German - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info