479878
3
Zoom out
Zoom in
Previous page
1/8
Next page
PAGE 04 - USER MANUAL USER MANUAL - PAGE 05
2.6 - SYSTEM DISARMING
2.7 - ALARM MEMORY
Press the unlock button on the original radio control of the vehicle; s
.
(2.7) for possible causes and signaling.
.
ystem disarming is confirmed by
two siren chirp (if feature has been modified) and two flashes of the turn indicators
An alarm condition will be signalled by five audio signals and five flashes from the turn indicators.
See relative paragraph
If during system disarming, the turn indicators flash 5 times and 5 audio signals (if feature has been
modified) are heard, the cause of the last alarm can be identified by the LED memory.
Turn the ignition key “ON” and look at the vehicle status LED; the blinking will indicate the last alarm
condition.
The visual signals will be repeated 3 times.
To interrupt, turn ignition key “OFF”.
The alarm trigger signals and relative causes are indicated in the table below
3.0 - NEW PIN-CODE PROGRAMMING
The procedure to program pin-code is specified here below as previously described, it is better to
personalize as customer has required.
In this example reported below, supposing that the pin-code is 5-4-6-7.
During PIN-CODE programming phase, if flashes are more than 9, this phase will be
invalid and the system will close the procedure.
!
!
!
!
!
!
!
!
!
!
With the system being disarmed, open the driver side door and bonnet and keep they open.
Turn the vehicle ignition key in “ON”-“OFF”-“ON”-“OFF”-“ON”-“OFF”-“ON” position; after the fourth
commutation, let the vehicle ignition key to “ON.
The indicators will flash once and two high pitched signals will sound (one brief and the other
longer) to indicate the system is in the programming mode.
Turn the vehicle ignition ket to “OFF” position.
After a three second pause, state LED will start with the first sequence of 9 flashes.
At the fifth LED flashing (corresponding at nr.5, first digit of the PIN-CODE), push and release the
button on the status LED.
After a three second pause, state LED will start with a new sequence of 9 flashes.
Athe fourth LED flashing (corresponding at nr.4, second digit of the pin-code) push and release the
button on the status LED.
After a three second pause, state LED will start with a new sequence of 9 flashes.
At the sixth LED flashing (corresponding at nr.6, third digit of the pin-code) push and release the
button on the status LED.
!
!
!
After a three second pause, state LED will start with the last sequence of 9 flashes.
At the seventh LED flashing (corresponding at nr.7, fourth digit of the pin-code) push and release
the button on the status LED.
No audio/visual signal will indicate the end of the procedure.
LED FLASHES ALARM CAUSES
Nr. OF ALARM
CYCLES
10
10
10
10
10
10
Starting attempt (+15/54)
Doors opening*
Bonnet opening
Boot opening
Volumetric or external sensor
Wire tampering
LED ON (1 second)LED OFF (2 seconds)
* Entry delay of 4 sec.
4.0 - EMERGENCY DISARMING BY PIN-CODE
The procedure for emergency disarming by pin-code is following, reported below.
Kindly note that the standard pin-code programmed is of the four digit 1-1-1-1.
The same number used for pin-code programmation (5-4-6-7) has been used also for emergency
disarming example.
During PIN-CODE disarming phase, if flashes are more than 9, the procedure will be
.interpret as a theft attemp
!
!
!
!
!
!
!
!
!
!
!
!
!
Cause an alarm condition.
Leave the system triggering for the standard alarm timing (about 30 seconds) and wait for the
“inhibit time between two alarm signalling” (LED switched off for 5”).
During this period push and release the push-button of the status LED.
the “emergency procedure disarming” and the LED will start
flashing.
At the fifth LED flashing (corresponding at nr.5, first digit of the pin-code), push and release the
button on the status LED.
After a three second pause, state LED will start with a new sequence of 9 flashes.
At the fourth LED flashing (corresponding at nr.4, second digit of the pin-code), push and release
the button on the status LED.
After a three second pause, state LED will start with a new sequence of 9 flashes.
At the sixth LED flashing (corresponding at nr.6, third digit of the pin-code) push and release the
button on the status LED.
After a three second pause, state LED will start with a new sequence of 9 flashes.
At the seventh LED flashing (corresponding at nr.7, fourth and last digit of the pin-code) push and
release the button on the status LED.
If the code is right, the end of the emergency disarming by pin-code will be indicated by the alarm
system with visual/acoustic signalling.
Vice versa, if the inserted numbers are wrong, the alarm system will start triggering again; in this
case, repeat all procedure.
From now and on the system is in
5.0 - WARRANTY CONDITIONS
This apparatus is guaranteed against all defects of fabrications for a period of 24 month from the
installation date shown on this warranty coupon, taking into consideration the 1999/44/CE.
Therefore, you are kindly requested to fill entirely the guarantee certificate included in this booklet and
to NOT REMOVE the guarantee label from the device.
Missing or tearing of this label, missing of one part of guarantee certificate or missing of the enclosed
sale document, will invalidate the guarantee.
The guarantee is valid exclusively to Gemini TechnologiesS.p.A.Authorized Service Centers.
The manufacturer will decline any responsibility for any eventual malfunctions of the device, or
electrical plant damages of the vehicle, due to improper installation, use or tampering.
This alarm system has exclusively a deterrent function against eventual thefts.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 821 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 821 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gemini 821

Gemini 821 User Manual - German - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info