479878
2
Zoom out
Zoom in
Previous page
1/8
Next page
1.0
2.0
6.0
7.0
8.0
9.0
12.0
16.0
17.0
- PRELIMINARY ADVICE.............................................................................................
- OPERATING DESCRIPTION.....................................................................................
2.1 - Complete system arming..........................................................................................
2.2 - Passive arming.........................................................................................................
2.3 - Arming inhibit time....................................................................................................
2.4 - System armed..........................................................................................................
2.5 - Alarm, inhibit time between alarms and alarm cycles..............................................
2.6 - System disarming.....................................................................................................
2.7 - Alarm memory..........................................................................................................
NEW PIN-CODE PROGRAMMING......................
EMERGENCY DISARMING BY PIN-CODE..........
WARRANTY CONDITIONS ..................................
- CONNECTORS..........................................................................................................
6.1 - 20-way connector.....................................................................................................
6.2 - 8-way connector.......................................................................................................
- COMPLETE ELECTRIC DIAGRAM...........................................................................
- .......................
...................................................................................
..........................................................
8.3 - Connections to hazard push-button..........................................................................
- CENTRAL DOOR LOCKING CONNECTIONS TO ARM SYSTEM............................
.........................
.............................................
9.3 - Connection to turn indicators....................................................................................
DIP-SWITCHES PROGRAMMING TABLE...............................................................
- SYSTEM PROGRAMMING.............. ....................................
........................................................................................
.........................................................................
12.3 - Passive arming.......................................................................................................
12.4 - 5) ...........................................................................
12.5 - Boot push-button polarity selection........................................................................
12.6 - Impulse
............................................
..............................................
..........................................................
..........................................................................
..........................................................................................
....................................................................................................
- TECHNICAL DATA...................................................................................................
-
USER MANUAL
INSTALLER MANUAL
3.0
4.0
5.0
10.0
11.0
13.0
14.0
15.0
- ......................................................
- .....................................................
- ......................................................
CONNECTION TO ACTIVATE TURN SIGNALS.................................
8.1 - Conventional connections.....
8.2 - Connections on vehicles with separate lines..
9.1 - Connection - door locking motor unit with separate radio receiver..
9.2 - Connection - door locking motor unit with lock switch.
- SELF-LEARNING OF TURN INDICATORS FLASHES............................................
-
....................................
12.1 - Optical signalling.....,......
12.2 - Acoustic signalling.........................
Arming of siren (art. 772 output
visual signalling selection..........................................................................
12.7 - Select negative in alarm for horn or additional siren...
- SYSTEM PROGRAMMING EXAMPLE......................
- ULTRASONIC VOLUMETRIC PROTECTION
14.1 - Connections and positioning........
14.2 - Sensor regulation.........
- SYSTEM RESET..
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE) DIRECTIVE.....
PAGE 02
USER MANUAL - PAGE 03
PAGE 03
PAGE 03
PAGE 03
PAGE 03
PAGE 03
PAGE 03
PAGE 03
PAGE 04
PAGE 04
PAGE 04
PAGE 05
PAGE 05
PAGE 06
PAGE 06
PAGE 06
PAGE 07
PAGE 08
PAGE 08
PAGE 08
PAGE 11
PAGE 11
PAGE 11
PAGE 11
PAGE 12
PAGE 12
PAGE 13
PAGE 13
PAGE 13
PAGE 13
PAGE 14
PAGE 14
PAGE 08
PAGE 09
PAGE 09
PAGE 09
PAGE 09
PAGE 10
PAGE 10
PAGE 11
PAGE 11
PAGE 11
TABLE OF CONTENTS
2.0 - OPERATING DESCRIPTION
2.1 - COMPLETE SYSTEM ARMING
2.2 - PASSIVE ARMING
Press the lock button on the original remote control of the vehicle; s
).
ystem arming is confirmed by a
siren chirp (if feature has been modified)and a flash of the turn indicators.
The system has a 30” pre-arming “neutral time” (indicated by LED permanently on
Once this function is programmed, the system is set to be passively armed about 60” after switching off
ignition and after opening and closing the last door.
System activation will be indicated by the normal visual and audio (if feature has been modified)
arming signal.
In case of passive arming, internal sensors and comfort output (automatic window
closing) will be excluded.
Opening a door 60” before the system is armed temporarily interrupts the procedure
which will resume once the door is closed.
USER MANUAL
2.3 - ARMING INHIBIT TIME
2.4 - SYSTEM ARMED
2.5 - ALARM, INHIBIT TIME BETWEEN ALARMS AND ALARM CYCLES
The inhibit arming time lasts approxiately 30” and is indicated by the LED on;
.
After the inhibit time the system is “armed” and ready to detect any theft attempt.
When the system is fully armed, the LED flashes.
Ithe system will indicate theft attempt
before another alarm starts, there are 5“ of “neutral time”.
The alarm signalling has 10 cycles of 30” each for input and system arming cycles.
it is possible to exit the
vehicle without triggering any alarm
s by visual/audio signals.
After the alarm has been triggered, but
1.0 - PRELIMINARY ADVICE
Dear Customer,
Th
.
same as 822 without engine immobiliser.
:
GEMINI 821:
e present manual illustrates the top version of the alarm system; not all functions, electrical
connections etc. will therefore apply to all models.
Before installing, you must identify your alarm model and refer to it for the correct instructions
The following signs, intended for the installer or the user, indicate particular functions or connections
as follows
!
For the user.
This sign highlights useful information.
For the installer.
This sign indicates that the functionning of the alarm can vary according to connections
and programming of the system or it simply provides useful indications for the
installation.
UK
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 821 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 821 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gemini 821

Gemini 821 User Manual - German - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info