810623

BeF Home Passive - HOT AIR FIREPLACE INSERTS Manual

6
Zoom out
Zoom in
Previous page
1/9
Next page
________________________________________________________________________________________________________________________________
Firma: BeF Home, s.r.o. Strana 6 (celkem 9) Platí od: 1. 4. 2014
Vydání: 4
There must be a safety pin on the smoke flue bellmounth to prevent slippage or turning out!
Fireplace insert with pull-up system door must be veneered to allow service and repair works. Veneer in the top part above the door of
fireplace must be built up from easy demountable material (Calsil etc.), or there must be service opening in the place of bearing (grilles,
thinning of coating etc.). Frame in the front part of insert with pull-up system must be built-in in accordance with scheme (pict. 4). It allows
later demounting in case of pull up system service. Holes in the cover of the pull-up system have to be through so the air can pass and carry
out the cooling of mechanism.
Pict.4
Convection air holes:
In the top part of the surround, it is necessary to provide non closable convection air holes for a convection air output, in the bottom part, there
is a need of convectional air input - minimal diameter depends on output of the fireplace insert, mentioned in the Equipment certificate. You
need to consider non effective parts of the grilles (20-40% of the grille area, depending on design also) when choosing the convenient grilles
for input/output of the convectional air and take into account also way of the using (in Equipment certificate, nominal output of the fireplace
insert is mentioned and the real output depends on the amount of wood in use, the real output can be for short period higher of 50%). The
minimal dimensions of the convectional air grilles for input and output are mentioned in the following chart:
Fireplace insert output (kW)
Convectional air input (cm2) – grille
dimension
Convectional air output – grille dimension
(cm2)
6-9
700
1000
10-15
850
1200
15-20
1100
1600
After the fireplace installation neither the air input nor the air vents can be restricted by building panels.
We recommend ordering a professional firm.
To prevent heat accumulation, the holes for convectional air must be open during heating. No lockable grates, ribs, blinds etc. can be installed
into the holes. In the top part the convection coating must be finished by the partition wall above the hole so as not to make a thermal pocket
(See surround diagram).
Convection cross-section between the insert and the coating as well as the insulation on the rear side – please check the chart with
measures of protection (see p.6)
Note: These minimal distances in accordance with the Equipment Certificate must be kept to on all heights and widths of the fireplace
insert so as to allow convection air to flow through.
To prevent accumulation of heat must be input and output grids convection air during heating operation still opening.
Convection air area: If a prefabricated area for convection air is not used (lining made of a galvanized sheet), it is necessary to maintain a
distance according to the chart on page n.4 between the fireplace insert and rear thermal insulation layer.
The fireplace insert assembly: The fireplace insert can be placed on a fitted base after the making of the thermal insulation as in the
installation instructions. The fireplace insert is connected with the chimney by the connecting piece (smoke flue).
Extension joint: It is necessary to have an extension joint at least 3 mm thick between the insert and the coating. The extension joint can
be stemmed by a rope or sealing tape.
RÁMEČEK
PRVEK OBEZDÍVKY
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BeF Home Passive - HOT AIR FIREPLACE INSERTS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BeF Home Passive - HOT AIR FIREPLACE INSERTS in the language / languages: English as an attachment in your email.

The manual is 0.71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info