Manual Unold 68415 (page 29 of 136) (English, German, Dutch, French, Spanish)

379790

Zoom out

Zoom in

1/136

STUFE/SIZE

This enables the following setting in the various programs:

ST. I / SIZE I = for a small bread weight, approx. 750-1.000 g

ST II / SIZE II = for a larger bread weigh, approx. 1.000-1.200 g

Please note, that this option is only available in the programs

BASIS, VOLLKORN, HEFEKUCHEN. The respective setting is

indicated by an arrow in the LCD display. Please note also our

recommendations in the recipes.

PAUSE FUNCTION

The button PAUSE allows to interrupt the program, e. g. for

removal of the kneading blade or to brush the surface etc.

Press the button PAUSE for 1 second in order to interrupt the

programme. The display starts to blink. Now you can open the

breadmaker e.g. to remove the kneading blade. Then close the

lid and press the button PAUSE again for about 1 second. The

display stops blinking and the programme is continued.

Attention: Do not interrupt the programme for more than

5 minutes. In case of longer interruptions the rising of the dough

may be disturbed.

As long as the PAUSE function is activated (blinking display)

the START/STOP button is without function and the programme

cannot be stopped completely.

LIGHT

The interior of the breadmaker

TOP EDITION is fitted with

a lighting, which allows to

follow the actual state of the

programme without opening

the lid. Just press the button

LICHT and the light turns

on. To switch off the light

just press the button again.

After 1 minute the light is

automatically switched off.

EIGENPROGRAMM/USER PROGRAM

In addition to the other numerous programs provided by the

BACKMEISTER

you can also program your own USER PROGRAM.

You can change the basic time and program phase settings as

programmed at the factory or leave out various program phases.

This allows you to develop your own individual program for baking

bread or preparing dough. Below you will find a sample recipe.

First you should become familiar with the following information

on the basic programming and use of the USER PROGRAM.

USER PROGRAM

The program features the following options

Browning programmable

Timer programmable

Loaf size I and II not programmable

The default program is the same as for the BASIC program.

Phase Preset Programmable time frame

Total time 3:10 hours

Knead 1 10 minutes 6-14 minutes

Rise 1 20 minutes 20-60 minutes

Knead 2 15 minutes 5-20 minutes

Rise 2 25 minutes 5-120 minutes

Rise 3 45 0-120 minutes

Bake 45 minutes 0-80 minutes

Keep warm 60 minutes 0-60 minutes

The times can be programmed as shown in the table.

Proceed as follows:

Select the USER PROGRAM with the Menu button.

Select the desired phase with the ABSCHNITT button. Knead

1 and the programmed time 0:10 for this phase appear on the

display.

The time can be changed by means of the ZEITWAHL button.

Press it repeatedly until the desired time appears on the display

(past OFF, if necessary).

Confirm the change with the ABSCHNITT button. Press this

button again and the next program phase and the programmed

time will appear on the display: Rise 1 = and 0:20.

If the maximum programmable time for the respective program

phase is exceeded by pressing the ZEITWAHL button, O will

appear on the display if this is possible according to the above

table. This phase is then skipped during the program.

Every programmed setting must be confirmed by pressing the

ABSCHNITT button, so you can continue programming the next

program phase.

Once you have programmed all phases to suit your preferences,

conclude the programming by pressing the ABSCHNITT button

and then the START/STOP button. The programmed time for the

user program appears on the display. The program then starts

either immediately or after the time set via the timer function.

THE FUNCTIONS OF THE BREADMAKER

Alarm function

The alarm sounds:

 whenever the MENU or ZEIT/time buttons are pressed,

 when pressing the programmebuttons to confirm each step,

 during the second kneading process, to remind you to add

seeds, fruit, nuts or other ingredients. Please note that this

function cannot be deactivated, e.g. in the time preset

function,

 at the end of the baking process, the appliance beeps often

during the keep-warm phase,

 at the end of the keep-warm phase several beeps remind

you that the appliance is now switched off and the bread

has to be taken out of the bread pan. Please note that this

function cannot be deactivated, e.g. in the time preset

function.

 The alarm function cannot be inactivated.

Repeat function after power outage

Should the electricity supply been cut off during the operation

of the Breadmaker, the appliance will re-start, on re-instatement

of the supply, automatically from the point arrived at when the

cut-off occurred as long as the interruption is not longer than

2 minutes. If the interruption in the electricity supply lasts

more than 2 minutes and the display shows the basic setting,

the Breadmaker must be re-started. This is only practical if the

dough was not further than the kneading phase when the break

occurred. If the program was already in the last rising cycle when

the power broke down and the interruption lasts over a longer

time, the dough cannot be saved and the program has to be

started again.

Safety functions

The lid should not be opened after the program has started, except

during the second kneading phase for adding of ingredients.

During the rising and baking phase the lid should never be opened,

as the bread may sink down.

If the temperature in the appliance, due to previous use, is too

high (above 40 °C) for a newly chosen program, when an attempt

to re-start is made, the display will show H:HH and an alarm

sound will be heard. Should this occur, remove the pan and wait

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Unold 68415 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 2,25 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Unold 68415 Manual

Product: