494335
4
Zoom out
Zoom in
Previous page
1/5
Next page
19
Standard settings
The phase coupler/repeater will automatically, from its factory
settings, transfer and repeat Marmitek X-10 commands from
one phase to the other. The signals are transmitted (repeated) to
all phases at the maximum transmission level. In general, the
phase coupler will operate best in the standard setting.
However, under special circumstances it may be necessary to
change the settings.
Please note:
We recommend that, if in doubt, you do not change
the phase coupler's settings.
!
Programming
20
Programming
Changing the FKX40 settings
Only in certain circumstances is it necessary to change the
settings of the phase coupler.
The following programming options are available:
Standard Optional Setup LED
Commands Indication
Repeater
2 x ABright Status LED 1: ON
Phase 1 ON*)
Repeater
2 x ADim Status LED 1: OFF
Phase 1 OFF
Repeater
2 x BBright Status LED 2: ON
Phase 2 ON*)
Repeater
2 x BDim Status LED 2: OFF
Phase 2 OFF
Repeater
2 x CBright Status LED 3: ON
Phase 3 ON *)
Repeater
2 x CDim Status LED 3: OFF
Phase 3 OFF
Coupler
2 x ON Receive LED 1: ON
Function ON*)
Coupler
2 x OFF Receive LED 1: OFF
Function OFF
21
Standard Optional Setup LED
Commands Indication
Default *) - - - Receive LED 3: OFF **)
Reset 2 x
LEDs and settings
to default All Lights On
according to factory
settings
*) Default factory setting.
**) In programming mode "Receive LED 3" will blink for 0.5 s when set-up commands
are being received.
Option description:
Repeater Phase 1 OFF: Received Marmitek X-10 commands
will not be repeated on this phase.
Repeater Phase 2 OFF: Received Marmitek X-10 commands
will not be repeated on this phase.
Repeater Phase 3 OFF: Received Marmitek X-10 commands
will not be repeated on this phase.
Coupler function OFF: Received Marmitek X-10 commands
will not be repeated to other phases.
This option can be used in test
situations.
Reset to factory settings: All options will be reset to the factory
settings.
22
Programming
Activating the programming mode:
The FKX40 must be set to the programming mode as follows:
Press the program button
for at least three seconds
(see Figure 3) until the
yellow LED lights up. The
Status/Receive LEDs now
display the activated
options.
Send the set-up commands
that correspond to the
desired setting(s) over the
power line to the FKX40
via a PMIX35.
Deactivating the programming mode:
Briefly press the program button or wait 60 seconds so that
the programming function deactivates automatically.
STATUS 1
PROGRAM
STATUS 1
STATUS 1
RECEIVE 1
RECEIVE 2
Phase Coupler/Repeater
FKX40
L1 L2 L3 N
RECEIVE 3
Figuur 3.
23
In programming mode the yellow LED "Program" is ON and the
Status/Receive LEDs indicate the activated options. The
programming mode can therefore also be used to check the
phase coupler's settings.
Observation: All LEDs are off. The yellow "Program" LED does not
blink every three seconds.
Checklist: Check whether there is any voltage and check the feeder circuit
of the circuit breaker to the FKX40.
Observation: The Status LED and the Receive LED for the same phase
are on constantly.
Checklist: Check the power connection for this phase on the FKX40.
Observation: One or more Receive and Status LEDs are blinking
constantly.
Step 1:
Set the FKX40 to programming mode and check whether Receive
LED 2 is on. If it is on, send the "Status ON" command twice over
the power line via a PMIX35 to deactivate the underlying
function. Receive LED 2 should go off. Exit the programming
mode. If this does not solve the problem, go to the next step.
Troubleshooting
24
Troubleshooting
Step 2: Set the FKX40 to programming mode and set option "Coupler
function OFF" (Receive LED 1: OFF). Exit the programming mode
and check whether this solves the problem.
Reset the FKX40 to programming mode and set option "Coupler
function ON" (Receive LED 1: ON). If this does not solve the
problem, go to the next step.
Step 3: Check the phase that corresponds to the blinking LED for any
component or equipment faults.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek FKX40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek FKX40 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info