494335
3
Zoom out
Zoom in
Previous page
1/5
Next page
13
Marmitek is niet verantwoordelijk voor het disfunctioneren
van het Marmitek X-10 systeem als gevolg van in het gebouw
aanwezige apparatuur met emissiewaardes boven de
maximale toegestane niveaus zoals die gelden in residentiële,
commerciële en lichtindustriële omgevingen en zijn
vastgelegd in de EN 61000-6-3.
Toepassing Geldende Europese norm Marmitek X-10 huis
automatisering*
Immuniteit van Emissie van Immuniteit- en
de apparatuur de apparatuur emissienorm
Residentieel 61000-6-1 61000-6-3 Compatibel/
Commercieel voldoet
Licht-industrieel
* Voorwaarde daarbij is dat het gehele Marmitek X-10 systeem wordt
geïnstalleerd volgens de geldende instructies door een gecertificeerde en
getrainde Marmitek X-10 dealer.
L1 L2 L3 N
89,5
72 58
Afmetingen
Copyrights
Marmitek is a trademark of Pattitude B.V., FKX40™ is a trademark of Marmitek B.V. All rights reserved.
Copyright and all other proprietary rights in the content (including but not limited to model numbers, software,
audio, video, text and photographs) rests with Marmitek B.V. Any use of the Content, but without limitation,
distribution, reproduction, modification, display or transmission without the prior written consent of Marmitek is
strictly prohibited. All copyright and other proprietary notices shall be retained on all reproductions.
20315 - 20100929
Marmitek X-10
Phase Coupler/Repeater
type FKX40
STATUS 1
PROGRAM
STATUS 1
STATUS 1
RECEIVE 1
RECEIVE 2
Phase Coupler/Repeater
FKX40
L1 L2 L3 N
RECEIVE 3
16
Marmitek X-10
FKX40 Phase Coupler
Role
The phase coupler transmits Marmitek X-10 commands that
enter from one phase to the other two phases. These
commands are repeated when transmitted to all phases.
17
Proceed with care!
Switch off the power before
starting assembly.
The FKX40 Phase Coupler/Repeater is
a DIN rail module and must be
installed in a distribution box.
Assembly
The phase coupler must be connected
to the load end of a 3-phase miniature
circuit breaker (3p+N) with a maximum
rated current of 16 A (see Figure 1).
Please note:
The FKX40 terminals are not
suitable for use as branching points
to other groups or loads.
Connections are, therefore, only
permitted as indicated in Figure 1.
!
!
Installation/assembly
STATUS 1
PROGRAM
STATUS 1
STATUS 1
RECEIVE 1
RECEIVE 2
Phase Coupler/Repeater
FKX40
L1 L2 L3 N
RECEIVE 3
L1 L2 L3 N
Figure 1.
18
Commissioning
Proceed with care!
Avoid touching live parts. Close the distribution
box before switching on the voltage.
As soon as the power is switched on again, the yellow LED
(Program) will blink once every three seconds (see Figure 2).
LED Function of the LEDs
Program (yellow) Blinks every three seconds.
Status (green) Blinks on every transmitted data package for this phase.
Receive (red) Blinks on every received data package for this phase.
!
STATUS 1
PROGRAM
STATUS 1
STATUS 1
RECEIVE 1
RECEIVE 2
Phase Coupler/Repeater
FKX40
L1 L2 L3 N
RECEIVE 3
STATUS
PROGRAM
Figure 2.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek FKX40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek FKX40 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info