494335
1
Zoom out
Zoom in
Previous page
1/5
Next page
Marmitek X-10
Fasekoppelaar/Repeater
type FKX40
STATUS 1
PROGRAM
STATUS 1
STATUS 1
RECEIVE 1
RECEIVE 2
Phase Coupler/Repeater
FKX40
L1 L2 L3 N
RECEIVE 3
Marmitek X-10
Fasekoppelaar FKX40
Functie
De fase-koppelaar koppelt Marmitek X-10 commando's, die via
de ene fase binnenkomen, door op de andere twee fasen.
Daarbij worden de Marmitek X-10 commando's versterkt op alle
fasen verzonden.
2
Pas op! Eerst de spanning
uitschakelen voordat u met
de montage begint.
De FKX40 Fasekoppelaar/ Repeater is
een DIN rail module en dient in een
groepenkast te worden gemonteerd.
Montage
De fase-koppelaar dient op de
afgaande zijde van een 3-fasen
installatieautomaat (3p+N) met een
maximale nominaalstroom van 16 A
te worden aangesloten (zie figuur 1).
Let op! De klemmen van de
FKX40 zijn niet geschikt om
als aftakpunt naar andere groepen
of belastingen te gebruiken. Het aan -
sluiten anders dan weergegeven in
figuur 1 is derhalve niet toegestaan.
!
!
3
Installatie/montage
STATUS 1
PROGRAM
STATUS 1
STATUS 1
RECEIVE 1
RECEIVE 2
Phase Coupler/Repeater
FKX40
L1 L2 L3 N
RECEIVE 3
L1 L2 L3 N
Figuur 1.
In bedrijf nemen
Pas op! Vermijdt het aanraken van stroomvoerende
delen. Sluit de groepenkast alvorens de spanning in
te schakelen.
Zodra de spanning weer wordt ingeschakeld zal de gele LED (bij
program) eens in de drie seconden oplichten (zie figuur 2).
LED Functie van de LED's
Program (geel) Knippert eens in de 3 seconden.
Status (groen) Knippert per verzonden data pakket op deze fase.
Receive (rood) Knippert per ontvangen data pakket op deze fase.
!
4
STATUS 1
PROGRAM
STATUS 1
STATUS 1
RECEIVE 1
RECEIVE 2
Phase Coupler/Repeater
FKX40
L1 L2 L3 N
RECEIVE 3
STATUS
PROGRAM
Figuur 2.
Standaard instellingen
De fasekoppelaar zal standaard, vanuit de fabrieksinstellingen,
automatisch de Marmitek X-10 commando's van de ene fase
doorkoppelen naar de overige fasen. Hierbij zullen de signalen
met het maximale zendniveau (versterkt) op alle fasen worden
verstuurd. In de meeste gevallen zal de fasekoppelaar in de
standaard instelling het best functioneren. Onder bepaalde
specifieke omstandigheden kan het echter nodig zijn de
instelling te wijzigen.
Let op! Wij adviseren u om de instellingen van de
fasekoppelaar bij twijfel niet te wijzigen.
!
Programmeren
5
Programmeren
6
Wijzigen van de instellingen van de FKX40
Slechts onder bepaalde omstandigheden kan het noodzakelijk
zijn om de instellingen van de fasekoppelaar te veranderen.
De volgende programmeer instellingen zijn mogelijk:
Standaard Optioneel Setup LED
Commando's Indicatie
Repeater
2 x ABright Status LED 1: AAN
Fase 1 AAN*)
Repeater
2 x ADim Status LED 1: UIT
Fase 1 UIT
Repeater
2 x BBright Status LED 2: AAN
Fase 2 AAN*)
Repeater
2 x BDim Status LED 2: UIT
Fase 2 UIT
Repeater
2 x CBright Status LED 3: AAN
Fase 3 AAN*)
Repeater
2 x CDim Status LED 3: UIT
Fase 3 UIT
Koppelaar
2 x ON Receive LED 1: AAN
functie AAN*)
Koppelaar
2 x OFF Receive LED 1: UIT
functie UIT
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek FKX40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek FKX40 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info