555058
5
Zoom out
Zoom in
Previous page
1/12
Next page
The JA-80Y GSM communicator - 5 - MFJ55304
5.1. Language setting
Language of the text used by the communicator can be set by
instruction:
981 xx
Where:
01 EN English 10 FI Finnish
02 CZ Czech 11 NO Norwegian
03 SK Slovak 12 SV Swedish
04 NL Dutch 13 FR French
05 DE German 14 HU Hungarian
06 PL Polish 15 RU Russian
07 DA Danish 16 TR Turkish
08 IT Italian 17 SP Spanish
09 PT Portuguese
Note:
Set the language before editing the text in the system (change of
the language will change the text to the factory default)
Change of the language in the communicator will automatically
result in changing the language in the connected keypad (also the
wireless keypad if connected)
Set language will not be change when reset is performed
Example: by setting 98102 the Czech language will be set.
Factory default : 98101 = English
5.2. GSM signal strength measurement
Good quality GSM signals are necessary for the reliable functioning of
the communicator. Entering 922 starts GSM signal measurement. The
keypad then displays the signal strength in the range 1/4 to 4/4 and
measurement is repeated every second (indicated by beeps). This mode
allows a suitable location to be found for the control panel (or the GSM
antenna). Press the # key to exit GSM signal measurement.
The SMS reply to a STATUS interrogation now displays GSM signal
strength in the range 0/9 to 9/9.
The signal should read at least 2/4. In places with a weak signal we
recommended trying another GSM provider’s SIM card.
Warning: it is not recommended to use a high-gain or directional GSM
antenna to get a better signal, as this way the communicator would only
communicate with a single cellular base station and communication
would not be stable. Also be aware that the GSM system cannot work
properly if the distance from the cellular base station is longer than 30km
(even if the signal is strong enough) as the time delays in the data
exchange would be longer than acceptable to the GSM standard.
5.3. Programming tel. numbers for reporting to phones
See part 4.
5.4. Selection of the events reported to phones
The factory-default list of reported events and their assignment to
telephone numbers M1 to M8 can be altered by this sequence.
The complete list of reportable events is shown in the following table.
It is possible to select whether the event should be reported by an
SMS or by a phone call, or by both an SMS followed by a phone call
Each event has pre-programmed factory-default SMS text. These
texts can be edited (see 5.5). The acoustic signals for phone call
reporting are fixed and cannot be changed (e.g. an alarm is
indicated by a siren sound if a reporting call is answered)
List of events which can be reported to phones and their factory-default assignment to particular phone numbers
Phone number memory M
ec Event
1 2 3 4 5 6 7 8
01 Intruder alarm - instant S S SC SC SC SC C
02 Intruder alarm - delayed S S SC SC SC SC C
03 Fire alarm S S SC SC SC SC C
04 Panic alarm S S SC SC SC SC C
05 Number of permitted incorrect code-entries
exceeded
S S SC SC SC SC C
06 Alarm triggered during control panel
power-up
S S SC SC SC SC C
07 Tamper alarm S S S S S S
08 End of tamper alarm
09 End of alarm indication
10 Alarm cancelled by user S S S S S S
11 Setting S S
12 Unsetting S S
13 Partial setting S S
14 Codeless setting S S
15 External communication fault S S S S S S S
16 External communication restored
17 Fault S S S S S S S
18 Fault no longer present
19 Mains dropout longer than 30 minutes S S S S S S S
20 Mains dropout
21 Mains restored
22 Discharged battery S S S S S S S
23 Battery OK
24 Switching to Service Mode
25 Leaving Service Mode
26 PGX ON/OFF
27 PGY ON/OFF
28 Radio communication jamming present S S S S S S S
29 Internal communication fault S S S S S S S
30 Internal communication restored
31 Communication test
32 Unconfirmed alarm
Factory-default report assignment: S = SMS, C = call, SC = SMS followed by a call
External communication fault means a GSM network dropout longer than 15 minutes (if GSM network dropout indication is enabled)
The SMS information about a new picture on the server is sent to all phone numbers which are set to get reported event number 01 “Intruder
alarm - instant”. This information contains a link to the new picture on the server.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-80Y at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-80Y in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-80Y

Jablotron JA-80Y User Manual - English - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info