555058
7
Zoom out
Zoom in
Previous page
1/12
Next page
The JA-80Y GSM communicator - 7 - MFJ55304
Factory-default SMS report and instruction texts
n Factory text n Factory text n Factory text n Factory text
44 Device 332 Code 504 Panic alarm 0 Report from your
alarm:
45 Device 333 Code 505 Invalid code-entries exceeded
1 Device 46 Device 334 Code 506 Alarm when power turned on
2 Device 47 Device 335 Code 507 Tamper alarm
3 Device 48 Device 336 Code 508 End of tamper alarm
4 Device 49 Device 337 Code 509 End of alarm indication
5 Device 50 Device 338 Code 510 Alarm cancelled by user
6 Device 201 Control panel 339 Code 511 Setting
7 Device 202 Service code 340 Code 512 Unsetting
8 Device 203 Annual inspection request 341 Code 513 Partial setting
9 Device 204 Communicator 342 Code 514 Codeless setting
10 Device 205 Keypad 343 Code 515 External communication fault
11 Device 206 ARC code 344 Code 516 External comm. restored
12 Device 300 Master code 345 Code 517 Fault
13 Device 301 Code 346 Code 518 Fault no longer present
14 Device 302 Code 347 Code 519 Mains dropout over 30 minutes
15 Device 303 Code 348 Code 520 Mains dropout
16 Device 304 Code 349 Code 521 Mains recovery
17 Device 305 Code 350 Code 522 Discharged battery
18 Device 306 Code 400 System status 523 Battery OK
19 Device 307 Code 401 Set 524 Switching to Service Mode
20 Device 308 Code 402 Unset 525 Leaving Service Mode
21 Device 309 Code 403 Exit delay 526 PGX
22 Device 310 Code 404 Entrance delay 527 PGY
23 Device 311 Code 405 Alarm 528 Radio jamming present
24 Device 312 Code 406 Service mode 529 Internal communication fault
25 Device 313 Code 407 Maintenance mode 530 Internal comm. restored
26 Device 314 Code 408 Partial setting 531 Communication test
27 Device 315 Code 409 Discharged battery 532 Unconfirmed alarm
28 Device 316 Code 410 Tamper alarm 601 SET
29 Device 317 Code 411 Alarm memory 602 UNSET
30 Device 318 Code 412 Fault 603 STATUS
31 Device 319 Code 413 Power fault 604 MEMORY
32 Device 320 Code 414 Unknown status 605 PGX ON
33 Device 321 Code 415 Time: 606 PGX OFF
34 Device 322 Code 416 Last event: 607 PGY ON
35 Device 323 Code 417 Credit unknown 608 PGY OFF
36 Device 324 Code 418 Credit: 609 AUX ON
37 Device 325 Code 419 (internal use only) 610 AUX OFF
38 Device 326 Code 420 Error while processing command 611 CREDIT
39 Device 327 Code 421 Output turned on
40 Device 328 Code 422 Output turned off
41 Device 329 Code 501 Instant alarm
42 Device 330 Code 502 Delayed alarm
43 Device 331 Code 503 Fire
Numbers 01 to 50 for devices and
codes are automatically generated by the
communicator so it is unnecessary to
enter them in the text
The communicator always automatically puts numbers from 01: to 50: in front of Device or Code names.
Texts 0 to 532 are used to create SMS event reports
Texts 601 and 611 are SMS instructions (to control the system remotely by SMS)
Text 419 is for the internal use of the communicator, never edit it !
5.6. Enabling reporting to phones
Event reports can be enabled as follows:
800 all SMS and call reports disabled
801 all SMS and call reports enabled
802 all reports enabled except reports of setting and
unsetting by users 41 to 50 (i.e. their codes, cards and
key fobs). This allows setting and unsetting done by report
recipients (owners, bosses, etc.) not to be reported.
Factory default setting: 801 all reports enabled
5.7. Remote access
Remote access (by phone or Internet) can be enabled or disabled:
9030 disabled
9031 enabled
Factory default setting: enabled
5.8. Forwarding of incoming SMS messages
This feature enables the automatic forwarding of incoming SMS
messages which contain no valid instructions to the system:
9260 messages are not forwarded, but the communicator sends
them by CLIP protocol to the simulated phone line
9261 messages are forwarded to the first programmed tel.
number in memories M1 to M8 (e.g. if numbers are only
programmed in M5 and M6, then messages will be
forwarded to M5). The tel. number from which the SMS
was received will be shown at the beginning of the
forwarded text.
Factory default setting: messages are forwarded
5.9. SMS instruction confirmation
If the communicator receives a valid SMS instruction, the instruction
sender will be made aware of its successful execution by the reception
of a conformation SMS sent by the communicator. This confirmation
can be disabled as follows:
9270 disabled
9271 enabled
Factory default setting: enabled
5.10. Reaction to incoming calls
The communicator’s reaction to incoming phone calls can be set by:
904 x
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-80Y at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-80Y in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-80Y

Jablotron JA-80Y User Manual - English - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info