555058
3
Zoom out
Zoom in
Previous page
1/12
Next page
The JA-80Y GSM communicator - 3 - MFJ55304
if it is desired that the events be reported to the SMS phone connected
to the communicator then program tel. number 001 into the memory
SMS report text consists of: installation name, event name, number and
name of the event source (device or code), date and time. Example:
“Report from your alarm: setting 47: device Time 01.08. 11:27
if other events or texts should be reported to a particular number,
change the communicator settings (see 5.4 and 5.5)
when storing tel. numbers, if you key in 7 after the last digit of the
phone number (the symbol is also stored) and continue with one
more digit (1, 2, 3, 8 or 9), then if this tel. number calls the system, the
system will behave as if ” digit“ had been keyed in just after the first
ring, i.e. as if it had been entered manually on the system keypad –
see section 3.5. Example: entering 81 5 777 777 777
79
0
authorizes calls from tel. number 777777777 to trigger output PGY for
2 seconds (after the first ringing signal from this number the 9
command will be executed. The PGY output should be programmed for
a 2 sec. pulse function. This setting is suitable for opening an electric
door lock, automatic gate etc.
4.1. Programming
The most convenient programming is best done by a PC running
Comlink software or via the Internet and website: www.GSMLink.cz
or by
programming SMS – PRG sequence
Programming is also possible via the system keypad:
The control panel must be in Service mode - if it is not, enter 0 Service
code (factory default: 8080) while the system is unset.
Enter the relevant programming sequences – see the following description
To exit service mode press the # key
5. Programming sequences
Function Sequence Options Factory default
Language setting 981 xx
xx=01 to 17 where:
01=EN,02=CZ,03=SK,04=NL,05=DE,06=PL,07
=DA,08=IT,09=PT,10=FI,11=NO,12=SV,
13=FR, 14=HU, 15=RU, 16=TR, 17=SP
English
GSM signal strength
measurement
922
On keypad or in ComLink software range 0/4 to 4/4
In reply to STATUS SMS: range 0/9 to 9/9
exit by pressing #
-
Tel. number programming for
reporting to telephones
81 M xx..x 0
M = memory 1 to 8
xx..x = tel. number (max.20 digits)
keying in 9 = + and 7 =
81 M 0 erases the number in memory M
all M1 to M8 erased
Selection of events to report by
SMS
82 M ec x
Selection of events to report by
phone call
83 M ec x
M = tel. number memory from 1 to 8
ec = event code (see 5.4)
x=1 report, x=0 no report
M1 & 2 alarms by SMS
M3 & 4 alarms by SMS and call
M5 & 6 alarms by SMS and call +
Set/Unset by SMS
M7 alarms by call
M8 technical faults by SMS (to installer)
SMS text editing*
Texts can be edited by Comlink software or by SMS instruction:
code TXT n,text,n,text... or by www.GSMLink.cz
via Internet
see 5.5
Enable reporting to phones 80 x
x=0 disabled
x=1 enabled (all programmed by 82.. & 83..)
x=2 enabled without reporting
setting/unsetting by users 41 to 50 (codes,
cards & key-fobs) and master code
setting/unsetting
enabled
Remote access 903 x
x=0 disabled
x=1 enabled (by phone and Internet)
enabled
Forwarding of incoming SMSes 926 x
x=0 no, x=1 yes = if the incoming text is not an
SMS instruction it will be forwarded to the first
programmed number in memories M1 to M8
yes
SMS instruction confirmation 927 x x=0 no, x=1 yes (by SMS reply) yes
Reaction to incoming calls 904 x
x=0: no reaction
x=1 to 8: answers after 1 to 8 rings
x=9: answers after the 2
nd
call
answers after 5 rings (25s)
Simulated phone line function 951 x
x=0 tel. line (GSM gateway)
x=1 alarm system keypad
x=2 off
x=3 automatically calls an emergency tel.
number when the tel. receiver is picked up
tel. line
Emergency tel. number
952 xx..x 0
xx..x = tel. number (max.20 digits) erased
GSM signal dropout indication 921 x x=0 no, x=1 yes (15min. dropout =Fault) no
Phone microphone sensitivity 953 x
Phone speaker loudness 954 x
x=1 to 9 (9 = maximum) 5
Number to be periodically called
to maintain SIM card validity
924 xx..x 0 xx..x = tel. number (max.20 digits), 9240=erase
erased
Using an SMS instruction to
configure automatic SIM card
credit interrogation *
Via an SMS instruction to the alarm system: code CREDIT uu..u xx yyy zz where code = master or service
code, uu..u = GSM network command string to ascertain the credit (e.g. 104#) , xx=auto-interrogation
frequency in days, yyy=minimum acceptable balance, zz= the textual position at which the number showing the
balance starts in the reply message from the GSM provider. If the credit is lower than the minimum, the
provider’s SMS will be auto-forwarded to numbers M1 and M8 for someone to top up the pre-paid SIM card.
Getting your www.GSMLink.cz
registration code sent to your
mobile phone
910 xx...x 0
xx..x = your mobile phone number -
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-80Y at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-80Y in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-80Y

Jablotron JA-80Y User Manual - English - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info