555058
4
Zoom out
Zoom in
Previous page
1/12
Next page
The JA-80Y GSM communicator - 4 - MFJ55304
Automatic SIM card credit
interrogation
Credit balance checking is set by SMS instruction code_CREDIT_uu..u_xx_yyy_zz where uu..u =
instruction for the GSM network (e.g. 101# etc.), xx= period in days, yyy=minimum balance, zz=
the position in which the number showing the balance starts, If the reported credit balance is lower
than the set limit (yyy), the credit balance message from the provider will be forwarded to phone
numbers M1 and M8
Programming by SMS
System can be programmed remotely via SMS instruction code PRG seq, seq,... where seq is
programming sequence set also from the keypad (e.g. 8080 PRG 08080,201,# set the 10s exit
delay)
Triggering re-registration to the
GSM network
923
The communicator will unregister from the GSM network and then re-register. Also possible via
the SMS instruction: code GSM. Code = master, user or service code
Communicator reset 98080 Resets to the factory default settings and erases all phone numbers, text will not be changed
Memorizing the SIM card’s PIN
code in the communicator
920 xx..x 0
xx..x = new PIN, sequence 9200 erases the
PIN (to use a SIM card with a disabled PIN)
erased
Configuring the GPRS log-in
parameters*
by SMS instruction to the alarm system: code GPRS x..x,y..y,z..z where code = master or service code, x..x =
the APN, y..y = name, z..z = password (only enter the APN if the name and password are not required by the
GSM provider)
ARC main tel. number/IP address
01 a xx..x 0
ARC backup tel. number/IP
address
02 a xx..x 0
a=1=ARC1, a=2=ARC2, xx..x = tel. number
(max.20 digits) or IP address & port – for
example: 01 2 8 192 168 001 123 08080 0
(8= signifies an IP address, it must have 12
digits followed by a 5 digit port number).
Entering 01p0 or 02p0 will erase the
number/address
erased
Installation (alarm system) ID for
ARC use
03 a zz..z 0
a=1=ARC1, a=2=ARC2, zz..z = ID number
max. 8 digits 0 to 9 and 1=A to 6=F
(hexadecimal number)
0000
Selecting the ARC protocol 04 a x
a=1 ARC1, a=2 ARC2
x=0 CID, x=1 SMS CID, x=2 IP CID
CID
Selection of events to report to
ARCs
05 a ec x
a=1 ARC1, a=2 ARC2
ec event code (see 5.27)
x=1 report, x=0 no report
all events are reported
Defining the delay before data is
resent to an ARC
06 a x
a=1 ARC1, a=2 ARC2
x=0 to 9 min. (0=immediately, without delay)
1 minute
ARC communication checking
period
(The time to wait after the last report
before performing an ARC
communication check)
07 a hhmm
a=1 ARC1, a=2 ARC2
hhmm = hours and minutes after last report
2400 (24 hours after last report)
Enable ARC reporting (ARC2
backs up ARC1)
00 a x
a=1 ARC1, a=2 ARC2
x=0 reports disabled, x=1 reports enabled, x=2
(only for ARC2) = ARC2 backs up ARC1
ARC reporting disabled
Recording reports sent to ARCs in
the control panel memory
08 x
x=0 no (only records ARC communication
faults, if communication checks are enabled)
x=1 yes (all reports except communication
checks)
yes
Indicate an ARC communication
fault if a report is not successfully
received by an ARC within 110
sec of transmission.
09 x
x=0 no
x=1 yes
no
IP address for data transmission
013 xx..x 0
IP address and port in format – e.g..: 013
8 192 168 021 123 08080 0 (8 mark IP
address which must contain 12 digits, followed by
5 digits for the port.. Entering 0130 IP erase the
setting
77.104.220.129 7070
(img.jablotron.com)
Locking the ARC settings
901 xx..x 0
xx..x = an installer-defined locking code (4 to 8
digits). Entering this code and then exiting
service mode will lock the ARC settings
9010 will erase the code (= permanently
unlocked)
Unlocked
Unlocking the ARC settings
900 xx..x 0
xx..x = the locking code used by sequence
901
ARC programming can be temporarily
enabled in service mode by entering this
sequence. It will then relock on exiting service
mode.
These parameters effect reporting to the ARC and it is impossible to change them if the ARC settings are locked.
* These parameters cannot be programmed from the system keypad, but they can be programmed by sending SMS instructions or by Comlink software.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-80Y at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-80Y in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-80Y

Jablotron JA-80Y User Manual - English - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info