Manual Jablotron GD-04 (page 7 of 15) (English)

554882

Zoom out

Zoom in

1/15

GD-04 DAVID 7 MKS51202_OS1*

11.2.1. DTMF relay control

• Call David’s tel. number. After about 7 seconds, David responds with a beep on the line

(this means that the call has been answered) followed by relay X and Y status indication (in

this order): 2 short beeps = OFF, 1 long beep = ON.

• Enter the DTMF code. A relay switch-on is confirmed by a long beep, a switch-off by two short beeps.

• Terminate the call (David automatically terminates the call after 60 seconds).

• After the call has been terminated David reports the current relay status via SMS.

Note: Too weak a GSM signal in David’s or your location may result in DTMF control

malfunctions.

11.3. The GD-04R radio module

By plugging the GD-04R radio module into the digital bus connector (after the power supply has

been disconnected) your David acquires the following capabilities:

• Relay X and Y state transmission to UC or AC OASiS wireless

receivers.

• Input A to D activations via RC-8x OASiS wireless buttons or via JA-

8x OASiS wireless detectors.

• Relay X or Y control via RC-8x OASiS wireless buttons.

• Relay X or Y control via a TP-8x wireless thermostat.

The module has a built-in internal antenna. If necessary, a Jablotron

external antenna of type AN-80 or AN-81 can be applied to extend David’s

working range.

Note: The external antenna is essential when the GD-04A back-up module is used.

11.3.1. Transmitting X or Y relay status to an UC-82 or AC-82 receiver

Enter mode 4 on the receiver and press the XY button on David’s GD-04R module. This

establishes a connection so that the receiver’s relay status mirrors David’s relay status. There is

no limit to the number of UC/AC receivers which can be connected this way.

11.3.2. Wireless device input assignment and operation

Each input A to D can have one OASiS wireless device assigned to it. This way, triggering an

external wireless device has the same effect as GD-04 input activation by physical connection to

GND, effectively making the inputs radio-signal-activated.

Take the following steps to enroll a device:

1. Press and hold the ABCD button on the GD-04R module.

2. Entering enrollment mode is indicated after 5 seconds by flashing of the LED on the

GD-04R module – release the button.

3. Enroll up to 4 wireless devices to the GD-04R (send enrollment signals to the module). The

first device is assigned to the A input, the second one to the B input, etc. Wireless buttons

are enrolled by pressing them, wireless detectors by inserting their batteries. Enrollment is

confirmed by a long flash from the LED on the GD-04R.

Important: Enrolling the first device erases all the previously enrolled devices. Thus all

the desired devices should be enrolled in a single enrollment session.

4. Exit enrollment mode by pressing the ABCD button (enrollment is automatically terminated

after the fourth device has been assigned or after 40 seconds).

5. After enrollment mode termination, the LED on the module lights for approx. 5 seconds to

indicate enrollment data storage.

Notes:

• If the two buttons A and B are present on an RC-8x controller, the device can be enrolled by

pressing either A, B or A+B. The operational logic is then as follows: pressing A or A+B is

BCDXY

GD-04R

module

remove it if

external antenna

I can’t work out how to register new phone numbers to our David garage gate system - the only resident who knew how has moved away. It works fine with my phone which is registered but some people who have just moving in would like to add their numbers . Any help would be greatly appreciated! Submitted on 23-5-2020 at 15:54
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron GD-04 in the language / languages: English as an attachment in your email.

The manual is 0,26 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jablotron GD-04 Manual

Product: