554882

Jablotron GD-04 Manual

3
Zoom out
Zoom in
Previous page
1/15
Next page
GD-04 DAVID 3 MKS51202_OS1*
5. Insert the circuit board back to its position.
6. Do the wiring, see below.
4. Wiring
1. Power supply – use the +12V and GND terminals. Any
power supply adapter used should provide 12V DC
voltage and up to 500mA of current. If an LT-89 mains
adapter is used (a recommended option) wire the grey
marked conductor to GND. Do not turn the power supply
on until all input/output wiring has been done.
2. Output relay contacts – available
at the X1+X2 and Y1+Y2 terminals.
Each contact is fused to 5A. The
circuits which the contacts belong to
are protected from the remaining
electronics by a safety separator
and are capable of switching up to
5A at 250V AC. The following
example shows a light bulb control via the Y output relay:
3. Input terminals – marked A to D. The terminals respond to a
connection or disconnection to or from GND by sending an SMS
report. No external voltage supply can be connected to these
terminals – they can only be controlled via a potential-free
switch/contact. Example of wiring a switch to input A:
5. Initial powering up
4. Turn the power supply on, registering to the GSM network is indicated by the LED
flashing (if no indication occurs, check the power supply wiring).
5. After GSM registration the LED stops flashing (usually within 1 minute). Continued
flashing indicates a GSM registration fault. Disconnect the power supply and check that a
valid SIM card has been correctly installed into the device, see 2 and 3).
6. Send the SMS instruction STATUS to David’s SIM card number.
7. David responds by a status report, e.g. STATUS: A0,B0,C0,D0,X0,Y0,GSM:80% (which
means that all A to D inputs and both the X and Y relays are switched off and that the GSM
signal strength is 80%). Depending on the GSM network traffic the response may take some
time. If no response occurs, verify that “STATUS” is spelt exactly right in the text of the
message and that you are sending the message to David’s correct SIM card number (repeat
the previous step).
6. Programming
6.1. Via the Internet
The simplest way to program David is via the web site www.david.jablotron.cz.
You fill in all the required parameters in a form on a single web page, press the Send button,
and the Jablotron web server will forward the settings to your David via the GSM network.
Performance of a successful transfer is confirmed from David by an SMS reply "PROGRAM OK"
to your mobile phone.
Switch
12V DC
power supply
( adapter)LT-89
_
+
230V/50Hz
Light bulb
3 …


Need help? Post your question in this forum.

Forumrules
1

Forum

jablotron-gd-04

Reset search

  • I can’t work out how to register new phone numbers to our David garage gate system - the only resident who knew how has moved away. It works fine with my phone which is registered but some people who have just moving in would like to add their numbers . Any help would be greatly appreciated! Submitted on 23-5-2020 at 15:54

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron GD-04 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron GD-04 in the language / languages: English as an attachment in your email.

The manual is 0,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info