Manual Huvema HU 1010 B-4 SINO (page 22 of 48) (English)

627060

Zoom out

Zoom in

1/48

CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED

6. insTallaTion

6.1 UnpackinG

Unpack the wooden crate and use clamping plates and ringbolts to hoist the lathe. Place the support and tailstock

in a way that keeps the machine in the balance. When unpacking the machine, pay attention that the thread cutting

axis, the spindle, the hand wheels or other protruding parts don’t get damaged.

6.2 cleaninG

All bright parts have been coated. Use kerosene to remove the layer of grease on all bright parts and the gear

transmission before using the machine. Do not use paraffin, acetone or another solvent. Coat all bright parts with

acid-free oil and grease, especially the slide ways.

Warning!

Lubricate the machine in accordance with the regulations before using the machine.

6.3 insTallaTion

Place the lathe on a solid foundation with enough room for service and maintenance (fig. 2). Pour concrete around

the foundation bolts after setting these in the accurate positions. After solidification of the concrete, place the

machine on the foundation and tighten the foundation bolts (diam. 12 mm). Check adjustment with a spirit level in

longitudinal and transversal direction.

6.4 power sUpply

Warning

The machine must be connected to the power source by a qualified electrician.

The power supply has to be connected by means of a separate connecting clamp. The electric wires

are connected to the main connection at the rear of the headstock. Confirm that the power at the location is the

same as the rating of the lathe before plugging the lathe in. The lathe must be properly grounded. The main motor

turns clockwise (seen from the pulleys); the main spindle should turn counter-clockwise (seen from the tailstock).

Exchange 2 of the 3 phases if the motor turns in the wrong direction (fig. 3).

7. lUbricaTion

7.1 headsTock

The headstock is filled with Shell Tellus 32 oil. Remove the oil plug to change oil. The oil plug is located in the

headstock (bottom left) and can be reached after removing the cover of the change gears. Check the oil level every

week and change oil three months after using the machine for the first time. After that, change oil once a year.

7.2 Gear box

An oil bad with splash lubrication lubricates the gears and other parts. There is an oil reservoir located on the bottom

of the gear box. Fill the reservoir with Shell Tellus 32 oil until the right level is reached. Check the oil level every week

by looking through the oil-level glass and change oil three months after using the machine for the first time. After

that, change oil once a year. To change oil, remove the oil plug located on the side of the headstock.

7.3 apron

Fill the apron with Shell Tellus 32 oil till the right level is reached. Check the oil level every day and change oil three

months after using the machine for the first time. After that, change oil once a year. To change oil, remove the oil

plug located at the bottom of the apron. Oil is filled up by removing the filler cap at the right side of the apron.

7.4 chanGe Gears

Lubricate the change gears once a month with machine oil or grease.

7.5 oTher parTs

Other oil supply points can be found at the levers of the gear box, the hand wheel of the apron, at the bed slide,

cross slide, tool slide, cutting thread dial, tailstock, thread cutting axis and the feed shaft: fill up with oil once in a

while. Lubricate worm transmission, half nuts en thread cutting axis twice a month. Coat the slide ways and all other

bright parts, like the tailstock spindle, the feed shaft, etc. once a day with a small film of oil.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 1010 B-4 SINO in the language / languages: English as an attachment in your email.

The manual is 7,37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 1010 B-4 SINO

Huvema HU 1010 B-4 SINO User Manual - Dutch - 48 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Huvema HU 1010 B-4 SINO Manual

Product: