627060

Huvema HU 1010 B-4 SINO Manual

21
Zoom out
Zoom in
Previous page
1/48
Next page
21
CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED
5. General descripTion
Figure 1 – Construction of the machine
1 Headstock 18 Foot brake
2 Speed switch High/Low 19 Spindle control lever
3 Electric control box 20 Hand wheel of longitudinal feed (traverse adjustment)
4 Chuck 21 Lever of hand wheel of longitudinal feed
5 Tool post 22 Chip tray
6 Work lamp 23 Apron
7 Compound rest 24 Feed shaft selector
8 Hand wheel of compound rest 25 Thread cutting lever
9 Coolant 26 Rack
10 Cross slide 27 Control rod
11 Tailstock spindle clamping lever 28 Lead screw
12 Tailstock spindle hand wheel 29 Gear box
13 Tailstock 30 Feed switch
14 Tailstock clamping lever 31 Feed switch
15 Tailstock set screw 32 Gear box cover
16 Feed switch (longitudinal/cross) 33 Feed switch (direction)
17 Bed 34 Speed selection lever
5.1 bed
The bed is made of a high-grade low vibration cast iron (FCD25). By combining high sidewalls with strong cross ribs,
a bed of low vibration and rigidity is produced. The two precision ground V-sideways are an accurate guide for the
support and tailstock. The main motor is mounted on the rear of the bed.
5.2 headsTock
The headstock is cast from a high-grade low vibration cast iron. It is bolted to the bed, using four screws and four
adjusting screws for alignment with the head. The large main spindle is mounted on two precision taper roller
bearings (#7212). The hole of the spindle measures 35 mm. A quick change of the belt can be accomplished by
easing the tension on the idler. The belt type used in this lathe has the advantage that it makes no noise at any
speed.
5.3 sUpporT
The bed slide is made from high quality cast iron; the sliding parts are smooth ground. It slides over the bed without
play and can be easily adjusted. The cross slide is mounted on the bed slide and moves on a dove tailed slide. Play in
the cross slide may be adjusted by means of the wedges. Use the hand wheel to move the cross slide. A graduated
collar is placed on the hand wheel; one graduated mark equals 0.0254 mm. The tool slide is mounted on the cross
slide and can be rotated 360º. The tool and cross slide travel on dovetailed slides and have wedges, adjustable nuts
and graduated collars. The four-way tool holder is mounted on the tool slide. For accurate results, tightening the hex
nut can lock the support.
5.4 apron
The apron is mounted on the bed slide and moves on a dovetailed slide. A half nut is fitted into the apron. The half
nut gibes can be adjusted from the outside. The half nuts are responsible for the connection with the thread cutting
axis. A gear shaft, moved by a hand wheel on the support, and a rack, which is mounted on the bed, achieve quick
travel of the bed travel.
5.5 TailsTock
The tailstock slides on a V-way and can be clamped at any location by means of a bolt. A MT2 spindle with graduated
scale is part of the tailstock. The clamping handle makes clamping of the spindle possible. By turning the hand
wheel, the spindle can be moved.
5.6 oTher parTs
The lead screw is located on the front of the bed and is connected to the gear box on the left side. The gear box is
made from high quality cast iron and is mounted on the left side of the bed. It is a 9-speed motor. Always change the
speed to bring the idler in the right position. The motor is mounted on the rear of the bed.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 1010 B-4 SINO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 1010 B-4 SINO in the language / languages: English as an attachment in your email.

The manual is 7,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 1010 B-4 SINO

Huvema HU 1010 B-4 SINO User Manual - Dutch - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info