627060

Huvema HU 1010 B-4 SINO Manual

24
Zoom out
Zoom in
Previous page
1/48
Next page
24
CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED
9.2.2 TUrninG direcTion of spindle
Use the coupling lever to select the turning direction.
9.2.3 selecTinG speed ranGe of main spindle
Choose the speed range by means of speed switch high/low and a lever with four positions. The four speeds (in the
high/low range) are displayed on the machine shield. Put both levers in the appropriate position for the requested
speed.
Warning
Only change the speed when the spindle has come to a standstill!
9.2.4 sTarTinG periode
It is recommended not to use the highest speeds when starting the machine for the first time. Proceed as follows:
Select a low feed speed and load the machine lightly, during 3 hours, at 460 RPM, then 2 hours, at 755 RPM, then 1
hour, at 1255 RPM.
Follow this order when putting the machine into operation.
Note: If not used, disconnect the pin of the thread cutting dial from the thread cutting axis to avoid wear.
9.2.5 hole ThroUGh spindle
Camlock DI-4”
Install jaw chucks, catch plates and other tools that are mounted on the spindle:
• check if the hole and the surface are clean,
• check if all camlocks are open,
• install the tool on the hole through the spindle and attach all camlocks (turn clockwise).
Mark off a reference line on the tools, in the extension of the reference line on the hole through the spindle. This
makes clamping a tool again much easier.
Note: For correct locking condition, each cam must be tightened with its index line between the two “V” marks
on the nose.
Warning
Do not interchange chucks or other attachments without checking each cam lock for correct locking!
9.2.6 adjUsTinG The camlock
Figure 4
Remove lock screw (B). Turn bolt (A) once in or out as required. Tighten lock screw.
Note: Each cam lock has a reference sign (C) to indicate the original setting.
9.3 Thread and feed selecTion
All available feeds and threads are adjusted by using the charts that can be found on the front of the cover.
9.3.1 manUal operaTion
The hand wheel is used to move the bed slide. The cross slide is moved by means of the hand wheel, that is fastened
on top of it, and the tool slide by using the hand wheel of the tool slide. The bed slide can be locked, by turning the
tightening nut clockwise.
9.3.2 replacinG The chanGe Gears
Remove the cover, loosen the hex nut of the locking bolt and. After that loosen the locking bolt of the suspen-sion to
replace the transmission gear. The drive gear can be replaced after loosening bolts 120 T and 127 T.
9.3.3 aUTomaTic feed operaTion
First, engage the lever for the feed direction and install the change gear 30 T on the transmission shaft and change
gear 127 T on the drive shaft. Turn the selector handle for feed/thread cutting counter-clockwise. Put the handles of
the gear box in position 1-8 e.g. A-E, to enable the feed shaft to turn. When the handle for the feed shaft is pulled out
and pushed upwards, longitudinal feed is achieved. By pushing the handle in and downwards, cross feed is achieved.
The feed direction is selected by using the handle on the headstock. There are 40 different speeds available for
longitudinal and cross feed. Choose the speed by moving the handles of the gear box.
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 1010 B-4 SINO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 1010 B-4 SINO in the language / languages: English as an attachment in your email.

The manual is 7,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 1010 B-4 SINO

Huvema HU 1010 B-4 SINO User Manual - Dutch - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info