627060

Huvema HU 1010 B-4 SINO Manual

25
Zoom out
Zoom in
Previous page
1/48
Next page
25
CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED
9.4 Thread cUTTinG
Connect the thread cutting axis by moving lever for selection of feed/thread range to the right and the lever
for thread cutting downward. The transmission (longitudinal travel) for thread cutting is obtained. The direction for
thread cutting is selected with the switch on the headstock. The desired thread cutting is selected by means of the
handles on the gear box.
9.5 Thread cUTTinG dial
The thread cutting dial is located on the right side of the apron and is used for thread cutting with the lead screw. For
an even thread, close the half nut at the desired line of the dial, for an odd number on a numbered line. The thread
cutting dial should stand on the same spot at every cut. To avoid wear, it is recommended to disconnect the pin of
the thread cutting dial from the lead screw if not used.
9.6 cross slide and Tool holder
A tool holder is mounted on the tool post. The upper part contains a 0-45
0
left/right scale. The vernier scale on the
hand wheels correspond with the type of machine (Metric or Whitworth).
9.7 TailsTock
The tailstock is used to produce small parts. It can be adjusted transverse by using the set screws, that are mounted
on both sides of the tailstock. First, make sure that the locking lever of the tailstock is loosened. Loosen the screw at
the back. First, loosen one set screw, than the other, until the desired position is obtained. Tighten both screw and
the locking lever. The tailstock pinole can be tightened with the handle.
10. adjUsTinG
When the lathe is installed and ready for use, it is recommended to check the machine alignments before
commencing work. Alignment and levelling should be checked regularly to ensure accuracy.
The V-belts can be reached after removing the back splashguard, the cover and the V-belt guard cover. The motor is
mounted at the back of the bed on a plate that can be adjusted vertically. The plate is clamped with two stay bolts
and nuts. The belt tension is adjusted by turning the two hex nuts at the top of the plate outwards. Check the pulley
settings by putting a builder’s level over the pulleys. Make sure that the pulleys stay in line.
Use the hex screw on the bottom side of the tailstock between the guides to adjust the locking lever of the tailstock.
Adjust the transverse guiding by adjusting the tapered key with the slotted bolt at the front of the cross slide. First,
loosen the bolt at the back of the cross slide and tighten the bolt on the front by turning clockwise. Tighten the bolt
at the back after making the adjustments.
Follow this procedure to adjust the guide of the tool slide, only now use the slotted bolt on the front of the tool post.
Wear of the cross bolt can be compensated:
Remove the protection plate at the back of the cross slide. Turn the hand wheel of the cross slide clockwise until the
end of the cross spindle is reached. Turn the bolt at the end clockwise, as far as needed. Do not over tighten the bolt:
a rotation of 45° matches a play of 0.125 (.005”).
The spindle bearing has already been adjusted. The right setting is 0,0050 mm (0,0002”), the spindle can still be
moved by hand.
Technical changes and developments can lead to small deflection in the specifications and descriptions above. This
also applies for the part lists and drawings.
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 1010 B-4 SINO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 1010 B-4 SINO in the language / languages: English as an attachment in your email.

The manual is 7,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 1010 B-4 SINO

Huvema HU 1010 B-4 SINO User Manual - Dutch - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info