571659
5
Zoom out
Zoom in
Previous page
1/10
Next page
GOSSEN Foto- und Lichtmesstechnik GmbH 5
3.2.5 Aperture priority mode
Select f with the function buttons
Set the desired aperture with the value buttons. The intermediate
1/10 stop values stored from the last measurement appear when
the aperture is preset. These are not valid, because the valid and
actual 1/10th stops will only appear after the next meter reading is
taken.
Measure by pressing the meas. button M
The measured shutter speed appears in the right-hand digital display
Automatic adaptation of the aperture in 1/10 stops to the measured shutter speed
Select other paired aperture/shutter values with the value buttons.
3.2.6 Exposure value EV
Select EV with the function buttons
Measure by pressing the meas. button M
The measured exposure value appears in the left-hand digital
display (accuracy: 1/10 stops) and the aperture as a rounded-off
mark on the analog aperture scale
Select with the value buttons other paired aperture/shutter speed values corresponding with this exposure value.
3.2.7 CINE scale (frames per second)
Select t with the function buttons
Select the desired Cine speed (f.p.s.) by increasing the
shutter speed setting beyond 1/8000 sec. After approx.
1 second the meter switches over to CINE speeds.
The symbol appears in the display. The CINE speeds
can be preset between 8 and 64 frames/second.
Measure by pressing the meas. button
The measured aperture appears in the lefthand digital display (accuracy: 1/10th stops) and additionally as a
rounded-off mark on the analog aperture scale
The displayed aperture applies to a 180 degrees shutter blade. Enter a COR value
in the function for other shutter blades as an extension factor:
V = 180 degrees / 0pen aperture angle.
3.3 Measurements outside the measuring range
The Digipro F will not produce any useful readings outside
its measuring range
If it is too dark or too bright, an E (= Error) appears in the
left-hand digital display and alongside
it for too dark, or for too bright.
3.3.1 Display outside the display range
If the symbol or appears in the right or left digital display
it indicates that the taken reading is outside the meter’s display
range.
When actuate value button t to enter the display range.
When actuate value button u to enter the display range.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gossen Digipro F at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gossen Digipro F in the language / languages: English as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gossen Digipro F

Gossen Digipro F User Manual - German - 9 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info