605083

FALLER 120171 Beschrankter Bahnubergang Manual

26
Zoom out
Zoom in
Previous page
1/28
Next page
Gate control
CV's:
CV Legend Default Range of values
7 Software Version 1-
8 Manufacturer identifier 85 -
47 HighByte address 0 1-255
48 LowByte address address = CV47*256 + CV48 1 1-255
49 Configuration: 0 1-255
Bit 7 0=DCC 1=Mot
Bit 0 =0 -> automatic
=1 -> non-automatic
50 Blinker time constant 67 1-255
Value * 10ms = On/off time
51 Fade time constant 5 1-255
Cross fading time from light to dark and vice versa
= Value * 200us * 256
The LED flashing frequency can be adjusted with the CV50. The value in the CV determines the LED on/off
time, namely:
on or off time = CV value * 10ms
The fade times for exits J111 and J112 can be adjusted with the CV51, namely:
Fade time = value * 200us * 256
The data format for digital operation and the digital operating mode is stored in CV49.
for CV49:
DCC: operating modes: automatic CV49=0
non-automatic CV49=1
Motorola: operating modes: automatic CV49=128
non-automatic CV49=129
Notice for CV49: Do not use other values! If CV49 was set to 128 or 129, the controls will now only res-
pond to the Motorola data format and can only be reversed to DCC mode through key programming.
General notices:
All CVs can only be programmed via DCC digital command station connected to the programming track out-
put.
Notice for CV8:
Programming any value in CV8 will reset all CVs to their factory defaults.
Function:
Start contact:
----------------
The start contact always starts automatic operation, regardless of the
status of the control at the time the contact is closed.
Digital operation:
---------------------
Digital mode 1: (CV49-Bit0=0)
A digital point command »red« corresponds to the start contact and triggers
the automatics. The respective point command »green« will be ignored.
Digital mode 2: (CV49-Bit0=1)
A digital point signal »red« closes the gate.
A digital gate signal »green« opens the gate.
Programming the key button:
-------------------------------------
The programming key button can only be used in idle mode
(gate up, LED and stop point off)!
1.) Press key button -> LED will blink 3 x
2.) Now operate a point on a Motorola centre the LED will blink 3 x, the address has been accepted.
The control system is set to Motorola data format.
When using a DCC station:
3.) Press key button again -> LED will blink 3 x
4.) Now operate a point on a DCC station the LED will blink 3 x, the address has been accepted.
The control system is set to DCC data format.
If no entry is to be made:
5.) Press key button again -> the LED will blink 3 x. The control system is returned to working mode.
Important:
-------------
If the control system was set to Motorola via key programming,
it cannot be programmed and read with a DCC programming
track. To return the control system from Motorola data format to
DCC data format, the control system must first be changed to DCC mode
via key programming.
Protecting the motor end stage and the stopping outputs:
------------------------------------------------------------------------
Rapid blinking LED -> motor output short circuit
LED blinks same as during programming -> stop point short circuit
26
… 26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for FALLER 120171 Beschrankter Bahnubergang at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of FALLER 120171 Beschrankter Bahnubergang in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info