605083
28
Zoom out
Zoom in
Previous page
1/28
Next page
Slagboombesturing
CV's:
CV Uitleg Standaard inst. Bereik
7 Software-versie 1-
8 Fabrikantcode 85 -
47 Adres HighByte 0 1-255
48. Adres LowByte Adres = CV47*256 + CV48 1 1-255
49. Configuratie: 0 1-255
Bit 7 0=DCC 1=Mot
Bit 0 =0 -> met automaat
=1 -> zonder automaat
50. Constante knippertijd 67 1-255
Waarde * 10ms = Aan- en uitschakeltijd
51. Constante verlichtingstijd 5 1-255
Verandering van het licht van licht naar donker en omgekeerd
= Waarde * 200us * 256
De knipperfrequentie voor de LEDs kan met behulp van CV50 ingesteld worden. De waarde in de CV
bepaald de in- en uitschakeltijd van de LED, met:
Aann- c.q. uitschakeltijd = CV-waarde * 10ms
De verlichtingstijd voor de uitgangen J111 en J112 kunnen met de CV51 ingesteld worden, met:
Verlichtingstijd = waarde * 200us * 256
In de CV49 is het dataformaat voor de digitale werking en de digitale bedrijfsmodus opgeslagen.
voor CV49:
DCC: bedrijfsmodus: met automaat CV49=0
zonder automaat CV49=1
Motorola: bedrijfsmodus: met automaat CV49=128
zonder automaat CV49=129
Opmerking met betrekking tot CV49: Gebruik geen andere waarden! Als de CV49 op 128 of 129 wordt
geprogrammeerd, reageert de besturing alleen nog op het Motorola dataformaat en kan
uitsluitend via de toetsenprogrammering teruggezet worden naar de DCC modus.
Algemene opmerking:
Alle CV's kunnen met slechts één DCC digitale centrale aan de programmeerspoor-uitgang
geprogrammeerd worden.
Opmerking met betrekking tot CV8:
Als in CV8 een waarde naar keuze wordt geprogrammeerd, worden alle CV's naar hun
fabrieksinstelling teruggezet.
Functie:
Startcontact:
---------------
Het startcontact start altijd de automatische afloop, ongeacht de
toestand van de sturing op het moment, waar het contact werd gesloten.
Digitale modus:
-------------------
Digitale modus 1: (CV49-Bit0=0)
Een digitaal wisselbevel »rood« komt overeen met het startcontact en start
de automaat. Het desbetreffende wisselbevel »groen« wordt genegeerd.
Digitale modus 2: (CV49-Bit0=1)
Een digitaal wisselsignaal »rood« sluit de slagboom.
Een digitaal wisselsignaal »groen« opent de slagboom.
Programmering via de toetsen:
---------------------------------------
De programmeertoetsen kunnen alleen in rusttoestand
(slagboom boven, LED en stopplaats uit) gebruikt worden!
1.) Toets drukken -> de LED knippert 3 x
2.) Nu aan een Motorla centrale een wissel bedienen de LED knippert 3 x en het adres werd
overgenomen. De besturing staat op Motorola dataformaat.
Als gebruik wordt gemaakt van een DCC centrale:
3.) Toets opnieuw drukken -> de LED knippert 3 x
4.) Nu aan een DCC centrale een wissel bedienen de LED knippert 3 x en het adres werd
overgenomen. De besturing staat op DCC dataformaat.
Als er geen invoer plaats dient te vinden:
5.) Toets opnieuw drukken -> de LED knippert 3 x. De besturing staat weeer in de werkmodus.
Belangrijk:
-------------
Als de besturing via de toetsenprogrammering op Motorola werd gezet,
kan deze niet via een DCC programmeerspoor geprogrammeerd en gelezen
worden. Als de besturing van Motorola dataformaat weer op het
DCC dataformaat teruggezet moet worden, zo moet de besturing eerst
via de toetsenprogrammering in de DCC modus worden gezet.
Bescherming van de motor-krachtversterker en de stopuitgangen:
-----------------------------------------------------------------------------------
LED knippert snel -> kortsluiting motoruitgang
LED knippert zoals bij de programmering -> kortsluiting stopplaats
28
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for FALLER 120171 Beschrankter Bahnubergang at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of FALLER 120171 Beschrankter Bahnubergang in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info