605083
25
Zoom out
Zoom in
Previous page
1/28
Next page
Schrankensteuerung
CV's:
CV Erklärung Voreinst. Wertebereich
7 Software-Version 1-
8 Herstellercode 85 -
47 Adresse HighByte 0 1-255
48 Adresse LowByte Adresse = CV47*256 + CV48 1 1-255
49 Konfiguration: 0 1-255
Bit 7 0=DCC 1=Mot
Bit 0 =0 -> mit Automatik
=1 -> ohne Automatik
50 Blinkerzeitkonstante 67 1-255
Wert * 10ms = Ein- und Ausschaltzeit
51 Blendzeitkonstante 5 1-255
Überblendzeit von Hell nach Dunkel und umgekehrt
= Wert * 200us * 256
Die Blinkfrequenz für die LED’s kann mit der CV50 eingestellt werden. Der Wert in der CV bestimmt die
Ein- und Ausschaltzeit der LED, mit:
Ein- bzw. Ausschaltzeit = CV-Wert * 10ms
Die Blendzeiten für die Ausgänge J111 und J112 können mit der CV51 eingestellt werden, mit:
Blendzeit = Wert * 200us * 256
In der CV49 ist das Datenformat für den Digitalbetrieb und die digitale Betriebsart gespeichert.
zur CV49:
DCC: Betriebsarten: mit Automatik CV49=0
ohne Automatik CV49=1
Motorola: Betriebsarten: mit Automatik CV49=128
ohne Automatik CV49=129
Hinweis zu CV49: Verwenden Sie keine anderen Werte! Wurde die CV49 auf 128 oder 129
programmiert, so reagiert die Steuerung ab sofort nur noch auf das Motorola Datenformat
und kann nur per Tastenprogrammierung wieder zurück in den DCC Modus versetzt werden.
Hinweis allgemein:
Alle CV's sind nur mit einer DCC Digitalzentrale am Programmiergleisausgang programmierbar.
Hinweis zu CV8:
Wird in CV8 ein beliebiger Wert programmiert, so werden alle CV's wieder auf ihre Werkseinstellung
zurückgestellt.
Funktion:
Startkontakt:
----------------
Der Startkontakt startet immer den automatischen Ablauf, unabhängig vom
Zustand der Steuerung im dem Moment, in dem der Kontakt geschlossen wird.
Digitalbetrieb:
-----------------
Digitalmodus 1: (CV49-Bit0=0)
Ein digitaler Weichenbefehl »rot« entspricht dem Startkontakt und startet die Automatik.
Der entsprechende Weichenbefehl »grün« wird ignoriert.
Digitalmodus 2: (CV49-Bit0=1)
Ein digitales Weichensignal »rot« schließt die Schranke.
Ein digitales Weichensignal »grün« öffnet die Schranke.
Tasterprogrammierung:
-----------------------------
Der Programmiertaster kann nur im Ruhezustand
(Schranke oben, LED und Stoppstelle aus) benutzt werden!
1.) Taster drücken -> die LED blinkt 3 x
2.) Jetzt an einer Motorola Zentrale eine Weiche betätigen die LED blinkt 3 x
und die Adresse wurde übernommen. Die Steuerung steht auf Motorola Datenformat.
Falls eine DCC Zentrale benutzt wird:
3.) Taster erneut drücken -> die LED blinkt 3 x
4.) Jetzt an einer DCC Zentrale eine Weiche betätigen die LED blinkt 3x und die Adresse
wurde übernommen. Die Steuerung steht auf DCC Datenformat.
Falls keine Eingabe stattfinden soll:
5.) Taster erneut drücken -> die LED blinkt 3 x. Die Steuerung befindet sich wieder im Arbeitsmodus.
Wichtig:
----------
Wurde die Steuerung per Tastenprogrammierung auf Motorola gesetzt, kann sie nicht
über eine DCC Programmiergleis programmiert und gelesen werden.
Soll die Steuerung vom Motorola Datenformat wieder auf das DCC Datenformat
zurückgesetzt werden, so muss die Steuerung zunächst per Tastenprogrammierung
in den DCC Modus gebracht werden.
Schutz der Motorendstufe und der Stoppausgänge:
----------------------------------------------------------------
LED blinkt schnell -> Kurzschluss Motorausgang
LED blinkt wie bei Programmierung -> Kurzschluss Stoppstelle
25
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for FALLER 120171 Beschrankter Bahnubergang at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of FALLER 120171 Beschrankter Bahnubergang in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info