478469

Yaesu FTM-10R Manual

48
Zoom out
Zoom in
Previous page
1/116
Next page
46 FTM-10R OPERATING MANUAL
While operating on the Club Channel, a message (up to 16 characters) can be sent, instead
of sending a voice. 20 kinds of messages can be programmed, and one of them can be
selected and transmitted with your ID.
Note: The Message Feature requires that all members (1) use the FTM-10R transceiver, (2)
store the same messages into the message slot, (3) store the same member list into the
member box, and (4) store the desired coordination frequency into the “Club Channel”.
The Message Feature does not send the Message through the repeater.
The Message Feature is not active when the CTCSS, DCS, or Pager is activated.
PROGRAMMING A MESSAGE
(Requires all members to set the same message into the same message slot in the same order.)
The FTM-10R has 20 message slots, including a factory-programmed message (EMER-
GENCY). The factory-programmed message of course can be overwritten at any time with
personalized messages.
1. Press and hold the
[
VOL/SEL
]
key for one second to activate the Menu mode.
When the display indicates the Clock, Stop Watch Timer, or Temperature, press the
[
VOL/SEL
]
key to change to the VFO or memory mode, then perform the above.
2. Rotate the DIAL knob to select Menu Item “F18 MES-
SAGE”.
3. Press the key to enable selection of this Menu Item.
4. Rotate the DIAL knob to select the desired Message slot
into which you wish to store a message. The LCD displays
the previously stored message.
5. Press and hold the key for one second.
Press the PTT key to clear the previously stored message,
if desired.
6. Rotate the DIAL knob to select the first character of the
message you wish to store, and then press the key briefly
to save the first character of the message and move on to
the next place.
7. Repeat the previous step to complete the message (up to 16
characters). If you make a mistake, press the key to move back to the incorrect
character, then re-enter the correct character.
Press the PTT key to delete all data after the cursor that may have been previously
stored erroneously.
8. When the Message entry is complete, press and hold in the key for one second.
If you decide to cancel programming a message, press the
[
VOL/SEL
]
key to exit to
normal operation.
9. If you wish to store another message, repeat steps 4 through 8 above.
10. Press the
[
VOL/SEL
]
key to save the new setting and exit to normal operation.
MESSAGE FEATURE
Number of Message
… 48 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FTM-10R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FTM-10R in the language / languages: English as an attachment in your email.

The manual is 5,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info