674747
29
Zoom out
Zoom in
Previous page
1/140
Next page
Page 27FT
DX
1200 OPERATING MANUAL
DISPLAY INDICATIONS
Clock
Indicates the current time.
To set the clock
1. 3ress and hold the
[
C.S
]
button until the clock
digits blink.
. (nter the present time via the number keys
[
BAND
]
keys).
3. 3ress the
[
ENT
]
button.
Multi-Function Display
This area usually displays the status of major func-
tions.
3ress the
[
S
T
W
X
]
buttons to select an indicator
for the desired function, then press the
[
SELECT
]
button to select either of the settings.
A
DVICE:
This area also shows the CW5TTY'$T$ texts,
SC23( level meters, memory channels, and
menu items.
VOX:
This is the 21 or 2FF indicator for the automatic
voice-actuated transmitter switching in the SSB,
$0, and F0 modes. The controls affecting V2;
operation are the 0enu items
181 VOX GAIN
”,
182 VOX DELAY
”, and “
183 ANTI VOX GAIN
”.
By proper adjustment of these controls, hands-free
voice-actuated operation is possible.
METER:
This indicator determines the function of the meter
during transmission.
PO
Indicates the 5F 3ower 2utput, from 0
to 10 Watts on transmit.
ALC
Indicates the relative $LC voltage.
SWR
Indicates the Standing Wave 5atio
Forward 5eÀected).
COMP
Indicates the speech compressor level
SSB mode only).
ID
Indicates the ¿nal ampli¿er drain cur-
rent.
VDD
Indicates the ¿nal ampli¿er drain volt-
age.
PROC
(
Processor):
This indicator enables the Speech 3rocessor for
SSB transmission. $djustment of the 3rocessor
level is accomplished via the
[
PROC/CAR
]
knob.
A
DVICE:
The Speech 3rocessor is a tool for increasing
the average power output through a compres-
sion techniTue. However, if the 3rocessor level
is advanced too far, the increase in compression
becomes counter-productive, as intelligibility
will suffer. We recommend that you monitor
the sound of your signal using the 0onitor with
headphones).
DNR:
This indicator turns the 0ain band VF2-$) re-
ceivers 'igital 1oise 5eduction circuit on and off.
$djustment of the 1oise 5eduction level is accom-
plished via the 0enu item “
110 DNR LEVEL
”.
MIC EQ:
This indicator enables the Three-Band-3arametric
0icrophone (Tuali]er. The (Tuali]er settings are
activated via the 0enu.
DNF:
This indicator turns the 0ain band VF2-$) re-
ceivers 'igital 1otch Filter on and off. This is an
automatic circuit, and there is no adjustment knob
for the '1F.
KEYER:
This indicator toggles the internal CW keyer on
and off. The .eyer sending speed is adjusted via
the front panel’s
[
MIC/SPEED
]
knob and the CW
Hang Time is adjusted via the 0enu item “
064
CW BK-IN DELAY
”.
ZIN/SPOT:
This indicator enables the CW receiver spotting
tone. By matching the S32T tone to that of the in-
coming CW signal precisely the same pitch), you
will be “]ero beating” your transmitted signal with
the freTuency of the other station.
29


Need help? Post your question in this forum.

Forumrules
1

Forum

yaesu-ftdx1200

Reset search

  • Green Light on VFO A and MEM is flashing and no audio. Even tried Factory Reset and still flashing. How do I fix this? Submitted on 6-12-2022 at 07:37

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FTDX1200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FTDX1200 in the language / languages: English as an attachment in your email.

The manual is 14,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info