674747
28
Zoom out
Zoom in
Previous page
1/140
Next page
Page 26 FT
DX
1200 OPERATING MANUAL
&RQ¿JXUDWLRQ,QGLFDWRU
TUNER
This indicator appears when the internal $utomatic
$ntenna Tuner is activated.
VOX
This indicator appears when the automatic voice-
actuated transmitter switches in the SSB, $0, and
F0 modes.
PROC
This indicator appears whenever the 'S3 Speech
3rocessor is activated.
MIC EQ
This indicator appears whenever the Three-Band
3arametric 0icrophone (Tuali]er is activated via
the 0enu.
NAR
This indicator appears whenever the receiver’s
narrow IF 'S3 ¿lter is engaged.
REC
This indicator appears while the optional Voice
0emory Unit is recording your voice message, or
the Contest .eyer is recording your CW keying.
PLAY
This indicator appears while the optional Voice
0emory Unit is playing back the recorded voice
message, or the recorded Contest CW keying.
[
+
]
/
[
-
]
'uring F0 repeater operation, a negative freTuen-
cy shift will be indicated by “[-]” while a positive
freTuency shift will be indicated by “[]”.
DNR
This indicator appears whenever the 'igital 1oise
5eduction feature is activated.
DNF
This indicator appears whenever the 'igital 1otch
Filter is activated.
VFO-B Frequency Display
Shows the sub band VF2-B) freTuency during Split
operation.
ADVICE:
When turning the
[
CLAR
]
,
[
MIC/SPEED
]
,
[
PROC/CAR
]
,
[
NOTCH
]
,
[
CONT/APF
]
,
[
SHIFT
]
, or
[
WIDTH
]
knob, each freTuency or
value will appear in this area for 3 seconds.
DISPLAY INDICATIONS
Tuning Offset Indicator
This indicates the relative offset of the CW-TU1(,
ȝ-TU1(, Clari¿er, etc.
S/PO Meter
2n reception, this indicates the received signal
strength from S-0 to S-60dB.
2n transmission, this indicates the 5F 3ower 2utput,
from 0 to 10 Watts.
ADVICE:
The S32 meter types can be changed to
$1$L2G or B$5 type via the menu item “
012
METER TYPE SELECT
”.
The S32 meters can be set to the 3eak-hold
function B$5 type only) via the menu item “
013
BAR MTR PEAK HOLD
”.
DSP Display
This indicator is used for viewing the status of the
'S3 C21T2U5, 12TCH, WI'TH and SHIFT).
Key Function Display
ANT
(
1, 2
)
:
Indicates which antenna is selected by the front
panel
[
ANT
]
button.
IPO
(
AMP1, AMP2, IPO
)
:
Indicates which front end 5F ampli¿er is selected
by the front panel
[
IPO
]
button.
ATT
(
OFF, –6 dB, –12 dB, –18 dB
)
:
Indicates the attenuation level, selected by the
front panel
[
ATT
]
button.
R.FLT
(
3 kHz, 6 kHz, 15 kHz
)
:
Indicates the receiver IF 5oo¿ng Filter that is se-
lected by the front panel
[
R.FLT
]
button.
NB
(
OFF, ON, ON
[
NBW
]
)
:
Indicates the receivers “short-duration” 1oise
Blanker setting, which is selected by the front
panel
[
NB
]
button.
AGC
(
SLOW, FAST, MID
)
:
Indicates the $GC decay time setting, which is se-
lected by the front panel
[
AGC
]
switch.
28


Need help? Post your question in this forum.

Forumrules
1

Forum

yaesu-ftdx1200

Reset search

  • Green Light on VFO A and MEM is flashing and no audio. Even tried Factory Reset and still flashing. How do I fix this? Submitted on 6-12-2022 at 07:37

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FTDX1200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FTDX1200 in the language / languages: English as an attachment in your email.

The manual is 14,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info