674747
31
Zoom out
Zoom in
Previous page
1/140
Next page
Page 29FT
DX
1200 OPERATING MANUAL
REAR PANEL
ANT 1/2 Jacks
Connect your main antennas) here, using type-0
3L-) connectors and coaxial feed lines. The in-
ternal antenna tuner affects only the antennas) con-
nected here, and only during transmission.
Warning!
7KH95)YROWDJH#:ȍLVDSSOLHGWR
the TX RF section of the transceiver while trans-
mitting. Do not touch the TX RF section while
transmitting.
DC IN Jack
This is the 'C power supply connection for the
transceiver. Use the supplied 'C cable to connect di-
rectly to a 'C power supply, which must be capable
of supplying at least 3 $ #13.8 V'C.
GND
Use this terminal to connect the transceiver to a good
earth ground, for safety and optimum performance.
Use a large diameter, short braided cable for making
ground connections, and please refer to page for
other notes about proper grounding.
To prevent damage from lightning, atmo-
spheric electricity, electrical shock, etc., be
certain to provide a good earth ground.
μ-TUNE Jacks
These jacks are used to connect the optional 5F
Tuning .it, signal in and signal out.
ROT Jack
This covered 6-pin 0I1I-'I1 -ack accepts a cable
to connect to a Y$(SU
G-800DXA
-1000DXA/
-2800DXA
$ntenna 5otator listed models are cur-
rent as of early 013). You may control the antenna
a]imuth rotation and rotation speed) using the Func-
tion buttons on the front panel.
LINEAR Jack
This 10-pin output jack provides band selection data,
which may be used for control of optional accesso-
ries such as the
VL-1000
Solid-state Linear $mpli-
¿er.
TUNER Jack
This 8-pin output jack is used for connection to the
FC-40
(xternal $utomatic $ntenna Tuner.
RTTY/DATA Jack
This 6-pin inputoutput jack accepts $FS. input
from a Terminal 1ode Controller T1C) or an op-
tional interface unit it also provides ¿xed level 100-
mV #600 2hms) receiver audio output, and FS.
keying line.
PTT Jack
This 5C$ input jack may be used to provide manual
transmitter activation using a footswitch or other
switching device. Its function is identical to the
[
MOX
]
button on the front panel. The same line is
available at the
RTTY/PKT
jack for T1C control.
2pen-circuit voltage is  V'C, and closed-circuit
current is m$.
31


Need help? Post your question in this forum.

Forumrules
1

Forum

yaesu-ftdx1200

Reset search

  • Green Light on VFO A and MEM is flashing and no audio. Even tried Factory Reset and still flashing. How do I fix this? Submitted on 6-12-2022 at 07:37

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FTDX1200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FTDX1200 in the language / languages: English as an attachment in your email.

The manual is 14,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info