576540
38
Zoom out
Zoom in
Previous page
1/41
Next page
38 GB
Operation / Maintenance and careOperation
Remove the „+“ pole clamp (red)
14
from the
„+“ pole of the battery.
Measuring STANDBY / Battery
voltage
After connection to the grid, the appliance is on
STANDBY. The standby display
6
lights up. When
the clamps are connected, the battery voltage is
shown in the LCD (voltage display
9
). The segments
of the condition display
8
are empty.
If the voltage is below 3.8 V or above
15 V, the battery will not be charged. The
display briefly shows the error message
„Err“. The appliance goes on standby.
e®®
88.8
V
6 V battery
If the voltage range of the battery is measured as
between 3.7–7.3 V, only programme 1 can be se-
lected.
12 V batteries:
If a battery is recognised in the critical voltage
range of between 7.3–10.5 V, the appliance checks
whether a fully charged 6 V battery, or a discharged
12 V battery is present. After pressing the programme
selection button
10
to select a programme, the ap-
pliance carries out a control measurement for about
90 sec.
The display shows:
---
88.8
V
If after about 90 sec. between 7.3–7.5 V are detected
,
the 12 V battery is defective.
The appliance goes on standby.
Revitalising
If after about 90 sec. between 7.5–10.5 V are de-
tected, a 12 V battery is present.
Charging starts with a pulse charge for revitalising.
The voltage display
9
flashes. Once 10.5 V are
reached, the appliance switches to the other charge
steps.
Revitalising is the same for all the 12 V charge pro-
grammes.
Programme selection
NOTES:
If a battery is detected in the voltage range of be-
tween 3.7–7.3 V, the programmes 2–3–4 can be
selected.
The charging process takes place automatically.
Depending on the selected programme, the char-
acteristic charge curve is monitored for voltage,
time and temperature. Included are the diagnostics
programme, revitalising mode and retention charge.
(See principle representation programme 3 Fig. C)
Programme max. (V) max. (A)
1
6 V 7.3 V 0.8 A
2
*
14.4 V 0.8 A
3
*
14.4 V 3.8 A
4
*
14.7 V 3.8 A
Programme 1 „6 V“
(7.3 V / 0.8 A)
For charging 6 V batteries with a capacity of less
than 14 Ah.
Press the programme selection button
10
, to se-
lect programme 1. The symbol „6 V“ is displayed
on the LCD. During charging, the charge dis-
play
7
flashes and shows the progress of the
charge procedure (1–4 bars). When the battery
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ultimate speed ULGD 3.8 A1 - IAN 92517 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ultimate speed ULGD 3.8 A1 - IAN 92517 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info