and a network list will appear at the right side of
your screen. Select your target network, and
then click Connect.
34
The screen will appear as shown below. Enter
the network security key, and then click Next.
Instant Wireless Connection
Physical Description
Hardware Connection
Wireless Router Mode (Default)
As the supplement of wired LAN, TL-WR710N
enables the wired LAN to connect to the
Internet wirelessly.
As a wireless router, TL-WR710N create an
instant private wireless network and share
Internet to multiple Wi-Fi devices.
Access Point Mode
2
1
After hardware connection, please write down the
Wireless Password and SSID on the label of your
Router for later use. Both are case-sensitive.
SSID
: Wireless Network Name of TL-WR710N.
*
Wireless Password/PIN
: Pre-encryption password of
TL-WR710N.
*
LAN/WAN
: This port works as LAN in Access Point/Repeater/
Client/WISP Client Router mode and as WAN in Wireless Router
mode.
Reset
It is used to reset the Router to its factory defaults.
Indication
TL-WR710N LED:
Status
Solid Blue
The device is working properly.
Blinking
Condition 1: System is booting.
Condition 2: The Ethernet Cable or USB Device
is connecting to the product.
For more detailed information about
Reset
, please refer to
Appendix: Troubleshooting
.
Client Mode
TL-WR710N is used as a wireless network
card to connect the wireless network signal
or wireless router.
34
WISP Client Router Mode
In WISP mode, TL-WR710N enables multiple
users to share Internet connection from WISP.
5
For Windows 7
Click the icon at the bottom of your desktop.
Click refresh button, and then select the target
network. Click Connect.
34
Enter the Security key. Click OK.
For Mac OS
Click the icon at the right top of your
desktop. Click refresh button, and then select
the target network.
34
The screen will appear as shown below. Enter
the Password, and then click OK.
LAN
: This port works as LAN in Wireless Router/Access
Point/Repeater/Client/WISP Client Router mode .
USB
It is used to connect USB Flash or Hard Disk for le sharing and
Mobile devices for charging.
S/N:XXXXXXXXXXXX
Model:TL-WR710N(EU) Ver:1.0
Wireless Password/PIN:12345678
SSID:TP-LINK_663D6C
MAC:B0487A663D6C
Repeater Mode
TL-WR710N is used to extend the range of
wireless signal of the existing AP or wireless
router.
The LAN devices share the same IP from ISP
through Wireless or Wired port. While
connecting to Internet, the LAN/WAN
Ethernet port works as a WAN port at
Wireless Router mode. It’s suitable for most
hotel and home network with Plug-N-Play
after nishing Instant Wireless Connection.
In this mode, this device can be connected to a
wired network and transform the wired access
into wireless that multiple devices can share
together, especially for a home, oce or hotel
where only wired network is available.
In this mode, this device can copy and
reinforce the existing wireless signal to
extend the coverage, especially for a large
space to eliminate signal-blind corners.
In this mode, this device can be connected to
another device via Ethernet port and act as
an adapter to grant your wired devices
access to a wireless network, especially for a
Smart TV, Media Player, or game console only
with an Ethernet port.
In this mode, the device enables multiple
users to share Internet connection from
WISP. The LAN port devices share the same IP
from WISP through Wireless port.
Go toStart > Control Panel > View network
status and tasks > Change adapter settings.
Right clickWireless Network Connection,
and select Properties. Double clickInternet
Protocol Version 4 (TCP/IPv4)in the item list.
12
Set up the TCP/IP Protocol in "Obtain an IP
address automatically" mode on your PC. Click
OK.
Click the icon at the right top of your
desktop. Then click Open Network
Preferences…. The screen will appear as
shown below. Choose AirPort and click
Advanced….
2
Set the Congure IPv4 as “Using DHCP”. Click
OK.
1
Go toMetro interface> Control Panel > View
network status and tasks > Change adapter
settings.Right clickWireless Network
Connection,
and select Properties. Double
clickInternet Protocol Version 4 (TCP/IPv4)in
the item list.
2
Set up the TCP/IP Protocol in "Obtain an IP
address automatically" mode on your PC.
Click OK.
1
The default SSID of the network is TP-LINK_xxxxxx
(The TP-LINK_xxxxxx is the SSID on the label. )
The pre-encryption function is enabled by default and the default Network key/Security key is the Password on the
label. The password is case-sensitive.
1.
2.
5
When you can see Connected as shown in the
following screen, you’ve successfully
connected to the wireless network.
5
When Connected appears behind the SSID,
you have successfully connected to the target
network.
5
When appears before the SSID, you have
successfully connected to the target network.
(This method is for connecting to the default Wireless Router Mode. If you want to configure Wireless Router Mode or choose other modes, please skip to Router Conguration.)
S/N:XXXXXXXXXXXX
Model:TL-WR710N(EU) Ver:1.0
Wireless Password/PIN:12345678
SSID:TP-LINK_663D6C
MAC:B0487A663D6C
IC: 8853A-WR710N
FCC ID: TE7WR710N
1PXFS
7
_
)["
.PEFM5-
83/
%FGBVMU"DDFTT
IUUQUQMJOLMPHJOOFU
6TFSOBNFBENJO
1BTTXPSEBENJO
.CQT8JSFMFTT/.JOJ1PDLFU3PVUFS
Reset
LAN/WANLAN
USB
Protected by
NAT Firewall
Wired Network
Cable
Wired Network
Cable
SSID: def
Connect the plug directly to the TL-WR710N to finish
hardware connection.
The provided power plug may differ from the picture due
to different regional power specifications. Here we take
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for TP-LINK TL-WR710N at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of TP-LINK TL-WR710N in the language / languages: English as an attachment in your email.
The manual is 2,19 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
