Manual Solo 879-12 (page 76 of 160) (English, German, French, Spanish)

655956

Zoom out

Zoom in

1/160

Operating and maintenance notes

ENGLISH 36

The following instructions are for authorised service workshops only.

x Screw out four screws (a) and remove starter housing.

x Remove the air guide (b).

x Remove Circlip (c) by using a special plier and remove

the washer (d).

x Remove rope pulley (e) and remove all pieces of the

old rope from the pulley and from the starter grip.

Don’t throw away the washer (f), but put it safe by

side. You need it for the install of the new rope.

x Thread in a new starter rope (No. 0063181, dia 4.0

mm, length 940 mm) as shown [don’t forget the

washer (f)] and knot both ends.

x Pull one knot and washer (f) into the starter grip and

the other knot into the rope pulley. Do not let the knots

or the rope ends protrude from the outside of the rope

pulley.

x Insert the rope pulley into the starter housing and turn

it left and right until it completely goes in the right

position.

x Reinstall washer (d) and circlip (c).

x Guide the rope into the recess (g) on the rope pulley

and use the rope to turn the pulley two turns clockwise

(pretension the spring). Holding the rope pulley with

one hand, remove the rope from the recess (g),

straighten out the twist in the rope with your other

hand, pull the rope tight, and hold.

Carefully release the rope pulley Î now the pulley's

spring force will wind the cable counterclockwise

around the pulley.

x Repeat three times. The starter grip must be upright

on the starter housing.

Important: With the cable pulled all the way out, it must still be possible to turn the pulley another

half turn against the return spring.

If this is not possible you have the spring to relax a little by one turn counterclockwise with the rope

clamped into the recess (g).

8.8 Replacing the starter rope (must only be done by an authorised workshop)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Solo 879-12 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 2,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Solo 879-12 Manual

Product: