619691

Snooper S6-R Neo Manual

18
Zoom out
Zoom in
Previous page
1/20
Next page
16
Operating Instructions
1. Starting Up
After you have successfully installed your S6 or S6-R and performed the
download it is time to perform the first start up. Firstly make sure your
vehicle is parked in as open a space as possible, clear of tall trees and
buildings so that the GPS extension antenna has a clear view of the sky
above. Next power the unit up by pressing Button 1 (please refer to
diagram on page 4). The LCD display will briefly read ’Snooper’ and will
then automatically change to the ’SEARCHING’ display. The S6 needs to
acquire a minimum of 3 satellites to work effectively. Once this has been
achieved the S6 will proceed to the standby screen (See Standby Screen
next in this section) and the satellite counter on the left hand side of the
display will indicate how many satellites your unit can currently see. As
soon as the standby screen is displayed your S6 is ready for use and will
now automatically alert you of any locations stored in its database (as
well as radar and laser alerts if you have the S6-RLD connected). A
variety of Audible and Visual alert patterns are explained later on in this
section. See ’Features and Settings’ to personalise your unit.
As the GPS engine and antenna have never been used before, the first
’Cold’ start up could take as long as thirty minutes. Once initialised,
subsequent start-ups will take as little as three minutes.
2. Standby Screen
The Standby Screen is the screen you will see when your unit is powered
up and successfully installed. It is the display you will see when the unit is
not currently detecting or locating a source of radar, laser or a stored
coordinate.
SPEED
30MPH
NW
CITY CANCEL MUTE MENU
21
Note: To return to the Menu screen from the Sub Menu screen, press
the button below ’Back’ (2) on the display. To return to the Standby
screen from the Menu screen press the same button, which will now say
Cancel . If no buttons are pressed on the device for a period of five
seconds the screen will automatically return to the Standby display.
SET PRE-ALERT - After selecting
’SET PRE ALERT’ in the ALERT
SETTINGS Sub Menu , the display
will read ’DISTANCE’ with either the
factory default warning distance or
your previous selection displayed.
To increase the distance that your
S6 detects from press the button
below the Up arrow (3) until the
distance you require is shown on the
display. To decrease the distance that your S6 detects from, press the
Down button (4) until the distance you require is shown on the display.
Once you have made your selection press the ’Select’ button (5). The
display will read ’SETTING CONFIRMED’ to confirm your selection and
will return to the Menu screen.
Note: To return to the Menu screen from the Sub Menu screen, press
the button below ’Back’ (2) on the display. To return to the Standby
screen from the Menu screen press the same button, which will now say
Cancel . If no buttons are pressed on the device for a period of five
seconds the screen will automatically return to the Standby display.
2. Radar/Laser detector settings - S6-RLD only.
This setting is only applicable if you have purchased the S6-R, or the S6-
RLD as an optional extra, and allows you to turn the RLD off in low risk
situations and choose between receiving both Radar and Laser alerts or
Laser only.
From the Standby screen press the
button below ’Menu’ on the LCD
display and then using the buttons
below the Up (3) and Down (4)
arrows on the LCD display, scroll
until ’RADAR & LASER’ is highlighted.
Then simply press the button below
’Select’ (5) on the display and again
using the buttons below the arrows
on the display, highlight your desired
setting, choosing either ’RADAR &
LASER’, ’LASER ONLY’ or ’OFF’.
Once you have made your choice
press the ’Select’ button. The screen
will read ’SETTING CONFIRMED’ to
confirm your selection and will return
to the Menu screen.
SUB-MENU
Back
Select
DISTANCE : 500M
2 3 4 5
2 3 4 5
1. ALERT SETTING
2. RADAR & LASER
3. AUTOMUTE
MENU
RADAR & LASER
LASER ONLY
OFF
MENU
BACK
SELECT
CANCEL
SELECT
BACK
SELECT
09.30
… 18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Snooper S6-R Neo at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Snooper S6-R Neo in the language / languages: English as an attachment in your email.

The manual is 2,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info