754156

Silvercrest SDB 1500 A1 - IAN 114903 Manual

10
Zoom out
Zoom in
Previous page
1/57
Next page
10 GB/IE
Start-up
with a standard commercially available descal-
ing agent or with a little vinegar.
Insert the plug into an earthed socket. When
the function display 13 lights up, the device is
switched on and the boiler has begun to heat up.
Hoover the floor to be cleaned before you start
to generate steam.
Start to generate steam by pressing the steam
button 16 (Fig. L).
ATTENTION! Never use the device without a
pad 8! Risk of damage and scratching to the
floor. The pad 8 is available at authorised
service centres.
Press the steam button 16 again to stop the
steam function.
ATTENTION! RISK OF BURNS! Take care
when removing the pad 8 that the steam
base 9 does not tip over.
Remove the plug from the socket. Wait for at
least 5 minutes until the steam base 9 and the
pad 8 have been allowed to cool.
Changing the pads
If you change from a hard floor to a soft floor
when cleaning, you should also change the
pad 8.
Remove the plug from the socket. Wait for at
least 5 minutes until the steam base 9 and the
pad 8 have been allowed to cool.
ATTENTION! RISK OF BURNS! Take care
when removing the pad 8a and 8b that the
steam base 9 is not knocked over.
Remove the pad 8a or 8b .
Place the new pad 8a or 8b under the steam
base 9 onto the relevant felt attachment 19
(Fig. J).
Insert the mains plug into the mains socket.
When the function display 13 lights up, the de-
vice is switched on and the boiler has begun to
heat up. You can now start steam operation.
Filling the water tank
during operation
If the water in the water tank 11 runs out, press
the steam button 16 to discontinue steam pro-
duction.
Remove the plug from the socket and remove -
as previously described - the water tank 11 .
Fill the water tank 11 with cold, still water.
In cases of particularly hard water (with a
water hardness of more than 2 mmol / l), use a
mixture of 50% tap water and 50% distilled
water.
Re-insert the water tanks - as previously
described - and continue steam operation.
Using accessories for
carpet cleaning
ATTENTION! This attachment is only suitable
for cleaning carpets and soft surfaces. Do not
use the attachment on hard surfaces.
Ensure that the pad 8 under the steam
base 9 is attached to the appropriate felt
attachments 19 .
Place the attachment 17 with the flat side on
the floor. Attach the device to the attachment 17
(fig. K).
The device is now ready for carpet cleaning.
Ending operation
Press the steam button 16 to cease steam
production.
Remove the mains cable 4 from the socket.
Empty the water tank completely 11 to avoid a
build-up of limescale caused by standing water.
ATTENTION! Wait for at least 5 minutes until
the steam base 9 and the pad 8 have been
allowed to cool! Risk of burns!
Remove the pad 8.
Wrap the mains cable 4 around the cable
winder 3 and 14 .
Press the handle release button 1.
114903_silv_Dampfbesen SDB 1500 A1_content_FI_NL.indd 10 11.06.15 17:08
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SDB 1500 A1 - IAN 114903 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SDB 1500 A1 - IAN 114903 in the language / languages: English, German, Dutch, Swedish, Finnish as an attachment in your email.

The manual is 2,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info