Manual Silvercrest SDB 1500 A1 - IAN 114903 (page 9 of 57) (English, German, Dutch, Swedish, Finnish)

754156

Zoom out

Zoom in

1/57

9 GB/IE

Before Initial Use / Start-up

Before Initial Use

Attaching the steam broom

Remove the device from the packaging.

Attach the motor body 2 to the steam base 9

(Fig. A).

Tighten both parts together using the retaining

screw 21 and a Phillips screwdriver (Fig. B).

ATTENTION! Check the seating of the retain-

ing screw 21 regularly. Otherwise the steam

base 9 may detach itself from the device.

Press the handle release button 1. Lift up the

handle 15 until it clicks into place on the motor

body 2 (refer to Fig. C and Fig. D).

Preparing the steam broom

Unroll the mains cable 4 completely. You can

lower the pivotable cable winder 14 to make

this easier.

Pull the release lever of the water tank 12

upward in the direction shown by the arrow

(Fig. E) and remove the water tank 11 .

Turn the water tank 11 over and remove the

seal (Fig. F).

Fill the water tank 11 to the lower edge of the

thread with cold tap water (Fig. G). Screw the

seal back on without using too much force.

ATTENTION! In cases of particularly hard

water (with a water hardness of more than

2 mmol / l), use a mixture of 50 % tap water

and 50 % distilled water.

Re-insert the water tank 11 into the device and

ensure that the water tank valve is correctly

seated on the ﬁlter inlet (Fig H). Then click the

water tank 11 into the appropriate position

and check for the correct seating.

Start-up

Note: You can only use the turbo broom 18 , the

steam function or both functions at the same time.

However, we recommend that you use the two

functions after one another and ﬁrst use the turbo

broom 18 to remove dust from the ﬂoor. Only

activate the steam function thereafter.

Note: There is a groove below the handle into

which you can clamp the mains cable so that it

does not hang in the way during operation.

Switching the turbo

brush on/oﬀ

Press the ON/OFF switch 5 to switch on the

turbo brush 18 (Fig. I). The turbo brush 18 be-

gins to rotate and removes dirt and dust from

the ﬂoor, and collects it in the dust collector 6.

ATTENTION! Do not clean the turbo brush 18

during this process. The steam base 9 could

tip over or the dust collector 6 could fall

down. Risk of injury!

Press the ON/OFF button 5 again to switch

oﬀ the turbo brush 18 .

Using the steam function

Only use the device in well-ventilated rooms.

Remove the plug from the socket.

Use the blue pad 8b for soft ﬂoors and the

white pad 8a for hard ﬂoors. Place the pad 8

under the steam base 9 onto the relevant felt

attachment 19 (Fig. J).

ATTENTION! Ensure that the water tank is full

to prevent operation without water - otherwise

the pump could burn through.

ATTENTION! Similarly check before use that

all objects and surfaces to be cleaned are heat

resistant and/or compatible. We recommend

that you follow the care instructions of the man-

ufacturer, particularly for treated terracotta and

wooden ﬂoors. Conduct a test on an area which

is not easily visible or on a sample piece.

ATTENTION! There is a risk that a white

edge may develop on the ﬂoor if the device is

allowed to rest in the same spot for an ex-

tended duration during operation. This edge is

not indicative of damage! You can remove it

114903_silv_Dampfbesen SDB 1500 A1_content_FI_NL.indd 9 11.06.15 17:08

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SDB 1500 A1 - IAN 114903 in the language / languages: English, German, Dutch, Swedish, Finnish as an attachment in your email.

The manual is 2,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Silvercrest SDB 1500 A1 - IAN 114903 Manual

Product: