Manual Seiko S351 (page 5 of 7) (English)

757537

Zoom out

Zoom in

1/7

■HOW TO USE THE TIMER 「TIMER」

分時 秒

Mode selector

Button

・The timer can be set for up to 99 hours, 59 minutes and 59 seconds in one second

increments.

・Once the timer is set, the set time is stored in memory and can be used repeatedly

unless it is canceled.

・The timer can be set either by entering a time with keys or by recalling the

calculation result obtained in the time calculation mode.

・The remaining time is displayed in one second increments, and the time elapsed

from the start of the countdown can also be displayed while the elapsed time

display key is kept pressed.

・After the set time is up, the timer continues counting to show the time elapsed from

the end of the countdown, with “−” sign attached before the digits, for example, “0”,

“−1”, “−2”, and so on.

Turn the mode selector to set the knob to “TIMER”.

If the timer is counting, press button to stop the timer and then press to reset it.

(The time set previously will be displayed.)

Press the clear/clear entry key, and then, use the number entry and time keys to

enter the desired time. The timer can also be set by pressing the recall key to recall

the calculation result obtained in the time calculation mode.

Ex. 1) To set 3 minutes and 15 seconds:

[C/CE] [3] [1] [5]Or [C/CE] [3] [分 (MINUTE)] [1] [5]

(For details, refer to “■ HOW TO USE THE TIME CALCULATION MODE”.)

Timer setting

Notes:

･ By pressing the clear/clear entry key after the timer is reset, the

set time stored in memory is canceled and the digits are reset

to “0′00″”.

･ The timer counts down up to 100 hours in total from the start of

the countdown and stops. If the timer is set to count down 5

minutes and continues counting down after the set time is up,

for example, it will automatically stop when “-99:55′00″” is

displayed.

Press button or to reset the timer. The time previously set, 

“5′00″” will be shown.

〈To check the time elapsed from the start of the countdown〉

While the elapsed time display key is kept pressed, the time

elapsed from the start of the countdown is displayed.

･ When the elapsed time key is released, the remaining time is

displayed again.

･ While the elapsed time display key is kept pressed, the time

shown on the display increases in one second increment.

･ While the timer is stopped, the time elapsed from the start of the

countdown is displayed while the elapsed time display key is

kept pressed.

Timer operation

Ex. 2) To recall the calculation result:

[C/CE] [Call]

The calculation result obtained in the time calculation mode will be displayed.

Notes:

・Even if the clear/clear entry key is not pressed, the time can be entered and set for the timer.

・A negative calculation result obtained in the time calculation mode can be displayed for the

timer by pressing the recall key. The timer, however, will not count down the time.

・The arithmetic operation keys ([＋], [−] and [＝]) does not work in the timer mode.

To start or stop the timer, press button . Restart and stop of the timer can be repeated by

pressing the button. The timer restarts counting down from the time shown on the display.

Notes:

・When the timer is stopped, “STOP” and “ ″” marks are displayed.

・While the timer is counting down, “ ″” mark is not displayed.

・When a negative time (a time having a minus sign) is set for the timer and button  is

pressed to start the timer, the error mark “Error” is displayed. In that case, press the

clear/clear entry key to reset the digits to “0′00″” and enter a proper time.

After the set time is up, the timer continues counting down to show the time elapsed from the

end of the countdown, with “−” sign attached before the digits, for example, “0”, “–1”, “–2”, and

so on.

When the timer is stopped and button is pressed, the timer is reset and the time

previously set is displayed. The set time can be used repeatedly unless it is canceled.



Notes:

･ By pressing the clear/clear entry key after the timer is reset, the

set time stored in memory is canceled and the digits are reset

to “0′00″”.

･ The timer counts down up to 100 hours in total from the start of

the countdown and stops. If the timer is set to count down 5

minutes and continues counting down after the set time is up,

for example, it will automatically stop when “-99:55′00″” is

displayed.

Press button or to reset the timer. The time previously set, 

“5′00″” will be shown.

〈To check the time elapsed from the start of the countdown〉

While the elapsed time display key is kept pressed, the time

elapsed from the start of the countdown is displayed.

･ When the elapsed time key is released, the remaining time is

displayed again.

･ While the elapsed time display key is kept pressed, the time

shown on the display increases in one second increment.

･ While the timer is stopped, the time elapsed from the start of the

countdown is displayed while the elapsed time display key is

kept pressed.

■HOW TO USE THE STOPWATCH 「STOP-W.」

・The stopwatch can measure up to 99 hours 59 minutes and 59 seconds in one second increments.

After 100 hours, it will start counting again from “0” and continues counting.

・Split measurement is possible.

・The stopwatch can be set to count from a desired time up to 99 hours 59 minutes and 59 seconds

in one second increment.

・The starting time can be set by entering a time with the number entry and time keys or by recalling

the calculation result obtained in the time calculation mode.

Turn the mode selector to set the knob to “STOP-W.”.

If the stopwatch is counting, press button to stop it and then

press button to reset it.

・To start and stop the measurement, press button .

Restart and stop of the stopwatch can be repeated

by pressing the button. The accumulated elapsed

time measurement is possible.

Start

↑

Restart and stop of the stopwatch can

be repeated by pressing button .

To start the measurement from the desired time

･ By entering a desired time, the stopwatch can count from

the set time instead of “0”, for example, 3 minutes and 15

seconds. In that case, the stopwatch displays the elapsed

time added by the set time.

･ The starting time can also be set by recalling the calcula-

tion result obtained in the time calculation mode.

If the stopwatch is counting, press button to stop it and

then press button to reset it.

Press the number entry and time keys to enter the

desired time, or press the recall key to recall the calcula-

tion result obtained in the time calculation mode.

Ex. 1) To set 3 minute and 15 seconds:

[C/CE] [3] [1] [5]

[C/CE] [3] [分 (MINUTE)] [1] [5]

(For details, refer to “■ HOW TO USE THE TIME CAL-

CULATION MODE”.)

Ex. 2) To recall the calculation result:

[C/CE] [Call]

The calculation result will be displayed.

Standard measurement

Stop

B B

Restart Stop

Stop

Reset

· · · ·

・The split time measurement function is

convenient in checking the elapsed time

while the measurement is in progress.

Start

↑

Measurement and release of the split time

can be repeated by pressing button .

Split time measurement

Split

AAA

Split

release Stop

Reset· · · ·

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Seiko S351 in the language / languages: English as an attachment in your email.

The manual is 0,32 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Seiko S351 Manual

Product: