644555
11
Zoom out
Zoom in
Previous page
1/12
Next page
english 13
Maintenance
Warning: WhenservicinguseonlyidenticalRyobireplace-
mentparts.Useofanyotherpartsmaycreateahazardor
cause product damage.
Warning: To avoid serious personal injury make sure the
belt/discsanderisturnedOFFandthecordisunplugged
from the power source before performing any maintenance
or adjustment.
General maintenance
Afterusingyourbelt/discsander,cleanitcompletelyand
lubricate all sliding and moving parts. Apply a light coat of
automotive type paste wax to the worktable to help keep
the surfaces clean.
Motor housing
Frequently blow out any dust that may accumulate inside
the motor housing.
Changing drive belt, Fig. 20.
• Usingaphillipsheadscrewdriver,removethetwoscrews
in the center of the pulley cover.
• Removethecover.
• Raisesandingbelttotheverticalsandingposition(see
Figure20).
• Next,loosenthehexheadsetscrew.Raisingthemotor
pulley releases the belt tension.
• Removetheolddrivebelt.
• Fitthenewdrivebeltonthedrivepulleyrstandthen
on the motor pulley.
• Test belt tension by squeezing the belt with your n-
gers.
• Adjustthebelttensionwiththehexheadsetscrewuntil
thereisabout1/4in.(6mm)ofgive.
• Tightenthebelttensionnutsecurely.
Note: Excessive tightness on the drive belt may cause in-
creased noise and overload the motor. Excessive looseness
on the drive belt may cause the drive belt to fail prema-
turely and make a severe chattering noise.
• Using a phillips head screwdriver, reinstall the pulley
cover and the two phillips head screws. Tighten secure-
ly.
EC Declaration of Conformity
We herewith declare, scheppach Fabrikation von Holzbearbeitungs-
maschinen GmbH, Günzburger Str. 69, D-89335 Ichenhausen that the
machine described below due to its con struc tion and design and in
the version delivered by us complies with the relevant provisions of
thefollowingECDirectives.
In case of a modification of the machine this declara tion ceases to be
valid.
Machine description:
Bench Grinder
Machine type:
BD9000,Art.Nr.5903301901/5903301903
RelevantECdirectives:
EC machine directive 2006/42/EG,
EC Low voltage directive 2006/95/EWG,
EC-EMV directive 2004/108/EWG.
Applied harmonized European standards
EN 12100-1, EN 12100-2, EN 13857, EN 60 204-1
Place, date:
Ichenhausen, 10.07.2011
Signature:
On behalf of Werner Hartmann (technical director)
Trouble shooting
Problem Possible Cause Help
Motordoesn’tstart
a) ON/OFFswitchdamaged.
b) ON/OFFcabledamaged.
c) ON/OFFrelaydamaged.
d) Fuse blown.
e) Motor burnt.
ad) Replacealldamagedpartsbeforeyou
use your machine again.
e) Contactyourlocalservicecentre.Every
attempt to carry out a repair, can be
dangerous if it is not done by skilled
personnel.
Machine gets slower
during work.
Too much pressure put on the workpiece.
Reducethepressureontheworkpiece.
Sanding belt comes off
the drive pulleys.
Beltdoesnotrunstraight.
Resetthetrack.
The wood gets burnt
during sanding.
a) Sanding disc or belt covered with grease.
b) Excessive pressure on workpiece.
a) Replacediscorbelt.
b) Reducepressureonworkpiece.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach BD9000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach BD9000 in the language / languages: English, German as an attachment in your email.

The manual is 0,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info