644555
10
Zoom out
Zoom in
Previous page
1/12
Next page
12english
ingknobclockwise1/4turn.
• Ifthesandingbeltmovesawayfromthedisc,turnthe
trackingknobcounterclockwise1/4turn.
• Turn theswitch ON and then immediately OFF again,
notingbeltmovement.Readjusttrackingknobifneces-
sary.
Squaring the worktable to the sanding disc, Fig. 12
• Unplugthebelt/discsander.
• Using a combination square, check the angle of the
worktable with the sanding belt.
• Iftheworktableisnot90°withthedisc,loosenthetable
lock knob and tilt the table.
• Adjustworktablesquaretothesandingdiscandretight-
en the table lock knob.
Note:Usetheadjustmentscrewbeneaththeworktableto
move the table further or closer to the sanding disc.
WARNING: Beforeattemptingtouseyourbelt/discsander
familiarize yourself with all operating features and safety
requirements.
Locking the switch, Fig. 13
• PlacetheswitchintheOFFposition.
• Wait until the belt/discsanderhascometoa full and
complete stop.
WARNING: Do not reach across the sanding disc to turn the
belt/discsanderONorOFF.Contactwiththesandingdisc
can result in serious personal injury. See Figure 13.
m Hints for work
Bevel sanding, Fig. 14
The worktable can be tilted from 0° to 45° for bevel sand-
ing. To tilt the worktable:
• Loosenthetablelockknobbyturningitcounterclock-
wise.
• Setworktabletodesiredangle.
Note: Positiontheworktablenotfurtherthan1/16in.(1.6
mm) from the sanding surface.
• Tightenthetablelockknobbyturningitclockwise.
Sanding small end surfaces using the miter gauge, Fig. 15
A miter gauge is included with your tool for increased ac-
curacy.Useofamitergaugeisrecommendedforsanding
small end surfaces on the sanding disc.
Note:Alwaysmovetheworkpieceacrossthesandingdisc
from the left side towards the right side.
Horizontal and vertical sanding, Fig. 16
Your belt/disc sander can sand both vertically and hori-
zontally. Depending on the workpiece, the work support
can be used with either the horizontal or vertical sanding
operation.
• Insertthehexkeyprovidedintotheholesinthepulley
cover. Loosen the screws by turning them counterclock-
wise.
• Movethesandingbeltintoaverticalpositionasshown
inFigure16.Verticalpositioncanbechangedusingthe
vertical set screw.
• Lockthesandingbeltbyretighteningthescrews.Note:
Sand long workpieces with the sanding belt in the verti-
cal position by moving the work evenly across the sand-
ing belt.
Surface sanding on the sanding belt, Fig. 17
• Holdtheworkpiecermly,keepingngersawayfromthe
sanding belt.
• Keep theend pressed rmly against the work support
moving work evenly across the sanding belt.
Note: Useextracautionwhensandingverythinpiecesand
when sanding extra long pieces, remove the work support.
Apply only enough pressure to allow the sanding belt to
remove the material.
Sanding curved pieces, see Fig. 18 and 19
WARNING: Neverattempttosandtheendpiecesofawork-
piece on the idler drum. Applying the end of the workpiece
on the idler drum could cause the workpiece to y up.
Failure to heed this warning could result in serious per-
sonal injury.
Sanding inside curves on sanding belt:
Always sand inside curves on the idler drum as shown in
Figure 18.
• Holdtheworkpiecermly,keepingngersawayfromthe
sanding belt.
• Keep the curve pressed rmly against the idler drum
moving work evenly across the sanding belt.
Note: Useextracautionwhensandingverythinpiecesand
apply only enough pressure to allow the sanding belt to
remove the material.
WARNING: Applying the workpiece to the right side of the
sanding disc could cause the workpiece kickback. Failure
to heed this warning could result in serious personal in-
jury.
Sanding outside curves on sanding disc:
Always sand outside curves using the sanding disc and
moving the workpiece from the left side of center as shown
in Figure 19.
• Holdtheworkpiecermly,keepingngersawayfromthe
sanding disc.
• Keepthecurvepressedrmlyagainstthesandingdisc
moving work evenly on the left side of the sanding disc.
m Electrical connection
The installed electric motor is factory connected ready for
operation.TheconnectionmeetstheapplicableVDEand
DlNregulations.
The connection made by the customer as well as any ex-
tension cables used must comply with all relevant regula-
tions.
Connectionandrepairworkontheelctricequipmentmust
be carried out by a qualified technician only.
Important note
The motor rating is S 1. This means that when overloaded
it switches off automatically. After a cooling period (can
vary) you may switch it on again.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach BD9000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach BD9000 in the language / languages: English, German as an attachment in your email.

The manual is 0,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info