644555
9
Zoom out
Zoom in
Previous page
1/12
Next page
english 11
by trained persons who are familiar with the machine
andhavebeeninformedaboutthedangers.Unauthor-
ized modifications of the machine exclude a liability of
the manufacturer for damages resulting from the modifi-
cations.
• Themachineisintendedforuseonlywithoriginalspare
parts and original tools from the producer.
• Any other use is considered to be not intended. The
manufacturer excludes any liability for resulting dam-
ages, the risk is exclusively borne by the user.
m Remaining hazards
The machine has been built using modern technology and
in accordance with recognized safety rules.
Some hazards, however, may still remain.
• Thegrindingwheelposes a dangerofinjurytongers
and hands by improper feeding or placement of tools.
• Dangerofinjuryfromthrowntoolsduetoimproperhold-
ing or feeding.
• Theuseofincorrectordamagedmainscablescanlead
to electrical injuries.
• Although having regarded all considerable rules there
may still remain not obvious remaining hazrds.
• Minimize remaining hazards by following the instruc-
tionsin”SafetyRules”,”Useonlyasauthorized”andin
the entire operating manual.
Commissioning
Installing sanding disc and disc guard, Fig. 4
WARNING: Do not connect to power supply until assembly
is complete. Failure to comply could result in accidental
starting and possible serious injury.
• Removethebackingfromthesandingdisc.
• Align perimeter of sanding disc with plate and press
firmly into position.
• Position disc guard against the lower onethird of the
disc, aligning holes as shown in figure 4.
• Usingthetwophillipsheadscrews,securelytightenthe
disc guard into place.
Installing/Replacing sanding belt, Fig. 5.
On the smooth side of the sanding belt, there is a direc-
tional arrow. The sanding belt must run in the direction of
the arrow.
• Pull the tension lever toward you to release belt ten-
sion.
• Placethesandingbeltoverthedrivedrumandidlerdrum
withthedirectionalarrowsrunningcounterclockwise.Be
sure the sanding belt is centered on both drums.
• Pushthetensionleverbackintoplacetoapplythebelt
tension.
Note: The tension lever is spring loaded so use extreme
caution when pushing the tension lever back into place to
avoid personal injury.
Mounting the worktable for use with the disc sander, Fig. 6
To use the worktable with the disc sander:
• Inserttheindexpinintotheholeasshowningure6.
• Position the worktable not further than 1/16 in. (1.6
mm) from the sanding surface.
• Usingahexkey,tightenthehexsetscrewsecurely.
Mounting the worktable for use with the belt sander, Fig. 7
To use the worktable for vertical sanding:
• Inserttheindexpinintotheholeasshowningure7.
• Position the worktable not further than 1/16 in. (1.6
mm) from the sanding surface.
• Usingahexkey,tightenthehexsetscrewsecurely.
CAUTION: To avoid trapping the workpiece or your fingers
between the table and the sanding surface, the table edge
should NEVER be further from the sanding surface than
1/16in(1.6mm).
Assembling work support, Fig. 8.
• Placetheworksupportovertheholesinthesideofthe
tool housing.
• Usingahexkey,fasteninplacewiththewashersand
socket head screws.
Mounting belt/disc sander to work bench, Fig. 9
Ifyourbelt/discsanderistobeusedinapermanentloca-
tion, it is recommended you secure it to a workbench or
otherstablesurface.Whenmountingthebelt/discsander
to a workbench, holes should be drilled through the sup-
porting surface of the workbench.
• Markholesonworkbenchwherebelt/discsanderistobe
mounted using holes in the base as a template for hole
pattern.
• Drillholesthroughworkbench.
• Place belt/disc sander on workbench aligning holes in
the base with holes drilled in the workbench.
• Insertbolts(notincluded)andtightensecurelywithlock
washers and hex nuts (not included).
Note:Allboltsshouldbeinsertedfromthetop.Installthe
lock washers and hex nuts from the underside of the work-
bench.
Clamping belt/disc sander to work bench, Fig. 10
Ifyourbelt/discsanderistobeusedasaportabletool,it
is recommended you fasten it permanently to a mount-
ing board that can easily be clamped to a workbench or
other stable surface. The mounting board should be of
sufcientsizetoavoidtippingwhilebelt/discsanderis
inuse.Anygoodgradeplywoodorchipboardwitha3/4
in. (19 mm) thickness is recommended.
• Mark holes on board where belt/disc sander is to be
mounted using holes in the base as a template for hole
pattern.
• Follow last three steps in section Mounting Belt/Disc
Sander to Workbench.
If lag bolts are used, make sure they are long enough to
gothroughholesinbelt/discsanderbaseandmaterialthe
belt/discsanderisbeingmountedto.Ifmachineboltsare
used, make sure bolts are long enough to go through holes
inbelt/discsander,thematerialbeingmountedto,andthe
lock washers and hex nuts.
Adjustments
WARNING: Beforeperformingany adjustment,make sure
thebelt/discsanderisunplugged fromthepowersupply
and the switch is in the OFF position. Failure to heed this
warning could result in serious personal injury.
Adjusting the belt tracking, Fig. 11
• Pluginbelt/discsander.
To check belt tracking:
• TurntheswitchONandthenimmediatelyturnitOFF.If
the belt tends to slide off the idler drum or drive drum,
the belt is not tracking properly.
To adjust belt tracking:
• Ifthesandingbeltmovestowardthedisc,turnthetrack-
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach BD9000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach BD9000 in the language / languages: English, German as an attachment in your email.

The manual is 0,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info