Manual Parkside PSBM 500 B3 - IAN 102531 (page 11 of 80) (English, German, Danish, French, Swedish, Finnish)

595357

Zoom out

Zoom in

1/80

GB IE

5. Drill the hole until the depth stop

(2) comes in contact with the

component part.

Inserting/replacing the tool

1. Open the keyless chuck (4) wide

(RELEASE) so that the tool can

be inserted. To do so, rmly hold

the rear sleeve (4a) of the keyless

chuck (4) and turn the front sleeve

(4b) in the anti-clockwise direc-

tion.

2. Insert the tool as far as possible

into the keyless chuck (4).

3. Close the keyless chuck (4) (GRIP)

in order to clamp the tool. To do

so, rmly hold the rear sleeve

(4a) of the keyless chuck (4) and

turn the front sleeve (4b) in the

clockwise direction.

4. To remove the tool again, rotate

the keyless chuck (4) and pull out

the tool.

Always use a universal bit holder

use using a screwdriver bits.

Operation

Do not use the device with-

out the additional handle. It

provides additional hold and

reduces the risk of injury.

Observe noise control and local

regulations.

Switching on and off

1. Connect the machine to the pow-

er supply.

Make sure that the net voltage

matches the voltage rating indi-

cated on the device’s type plate.

2. Switching on: Press the on/off

switch (8).

3. By using the on/off switch (8)

you can progressively control the

speed.

Gentle pressure: low speed

Increase pressure: higher speed.

4. Continuous operation: Press the

lock button (9). The on/off switch

(8) is locked.

5. Switching off: Release the on/off

switch (8).

For continuous operation, briey

press the on/off switch (8).

Pre-select speed

You can pre-select the maximum speed on

the speed adjusting ring. The on/off switch

can only be pressed up to the specied

speed.

1. Wait for the device to shut-down.

2. Set the desired speed

on the speed adjusting

ring (7).

Set the direction of rotation

The device’s direction of rotation can be

changed with the rotational direction

switch.

1. Wait for the device to shut-down.

2. Push the rotational direction

speed (6) into the desired posi-

tion:

Clockwise rotation: to drill

and screw in screws.

Anticlockwise rotation: to

loosen screws.

I was drilling concrete for to long and the Parkside PSBM 500 b3 stopped to run. Is there a fuse inside ? Is there a thermal switch inside ? Is the MOSFET replaceable ?
Submitted on 22-11-2020 at 15:34
Reply Report abuse
I was drilling concrete for to long and the Parkside PSBM 500 b3 stopped to run. Is there a fuse inside ? Is there a thermal switch inside ? Is the MOSFET replaceable ? Submitted on 22-11-2020 at 15:33
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PSBM 500 B3 - IAN 102531 in the language / languages: English, German, Danish, French, Swedish, Finnish as an attachment in your email.

The manual is 4,6 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PSBM 500 B3 - IAN 102531 Manual

Product: