Manual Omnistor 5002 (page 4 of 4) (English, German, Dutch, French)

667067

Zoom out

Zoom in

1/4

3. GEBRAUCH

Die Markise öffnet und schliest sich bei Betätigung des Schalters

automatisch.

Der Elektrische Strombegrenzer stoppt den Motor , wenn das Tuch

vollständig ausgerollt oder ingerollt ist.

Die Markise kann in jeder Stellung gestoppt werden. Bringen Sie den

Kippschalter in die neutrale Position. Stellen Sie den Schalter nach

Benutzung immer in die Neutralste llung, da es sonst zu einem

geringen Stromverbrauch kommt.

Bei Defekt oder Stromausfall kann die Markise mit der Handkurbel

bedient werden.

Ein unfreiwilliges Ausfahren der markise während der Fahrt ist durch

die Zwischenschaltung des Relais’ ausgeschlossen.

4. MÔGLICHE STÔRUNGEN:

Der Motor stoppt beim Einfahren zu früh: die Anschlu kabel des

Motors an der Steuerung (orange und braun) sind vertauscht.

Der Motor reagiert nicht: die Pole der Zufuhrkabel (+ und -) sind

vertauscht. Oder bei zu schnellem Schalten zwischen ein und aus,

kann es sein, da der Motor nicht reagiert. Schalter erst in den

neutr alen stand bringen.

5.TECHNISCHE DATEN:

- Die Anlage entspricht den EMC Richtlinien 89/336/EEC.

- Batteriespannung: 12V DC

- Nominaler Verbrauch:

Ausfahren: 2 - 3A

Einfahren: 4 - 6A

Maximaler Verbrauch (Strom bei blockiertern Motor): 12A

ELECTRICAL CONNECTION AND USE Read these

instructions carefully. No warranty will be allowed for wrong

installation.

CONTENTS

Electronic control kit ..............................................................................1

Flexible tube 20 cm...............................................................................1

Rela y..................................................................................................... 1

Platescrew DIN 7981 4,2 x 38............................................................... 3

Flat connectors F6,3 x 0,8......................................................................9

1. MOUNTING

Install the operation panel in such a way that the awning can be seen

from that spot. The operation panel can be opened by clipsing the grey

sides of the panel away. The holes for the wires leaving the panel can

be drilled in the back.

2. CONNECTION

Connect the wires as shown on the scheme.

Place an electric cable 2 x 2.5 mm_ from the battery to the switch via a

16A fuse in the + conductor. In order to avoid short-circuit, wait before

int roduci ng the fuse untill the electrical connection is completed.

It’s important to install the relay as shown on figure, in order to cut

the current to the motor while driving.

Pass the wires of the battery to the switch. Provide t hem with flat

connectors 6.3F and connect them to the clamps 4 (+) and 5 (-) of the

electronic control system.

Do the same with the motorw ires (orange and brown) but connect

them to t he clamps 6 and 7 of the control system. Watch the colour of

the w ires . The set curr ent limit for stopping the motor is not the same

for IN or OUT. When making a wrong connection the cu rrent could be

insufficient for closing the awning.

Introduce the fuse into the fuseholder and try operating.

3. USE

The awning is opened and closed automatically when you activate the

switch on the control panel. The electronic current limitation stops the

mot or automat ically w hen the fabric is completely unrolled or closed.

If you don’t want to open the awning completely, the rolling can be

interrupted at any intermediat e position by putting the switch in the

neutral position. Put the switch in the neutral position when the motor

doesn’t work, otherwise there still would be a limited consumption of

current.

In case of emer genc y ( e. g. no current or engine trouble) the awning

can always be operated manually with a handcrank.

While driving, unlikely opening of the awning is made impossible by the

security relay

4. POSSIBLE DISTURBANCES:

The motor stops while closing the awning: The connection of the

mot or wires (orange and green) is reversed.

The motor doesn’t function at all: The connection of the battery wires ( +

and -) is reversed. T he motor does n’ t reac t if the switch is suddenly put

in reversed direction. Put the swich in the neutr al position first.

5. TECHNICAL DATA

- The installation will meet EMC-standards 89/336/EEC

- Bat tery : 12V DC

- Nom inal consumption:

unrolling : 2 - 3A

roI ling up: 4 - 6A

maximal consumption (motor blocked): 12A

ORANGE

BROWN

BROWN = Brun / Braun / Bruin

ORANGE = - / - / Oranje

I can't get the awning to fit back in the cradle, I think the awning has dropped a little. How do I adjust it to fit back in the cradle? Submitted on 17-8-2020 at 11:37
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Omnistor 5002 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Omnistor 5002 Manual

Product: