609460

Nilfisk-ALTO SCRUBTEC R 466 Manual

81
Zoom out
Zoom in
Previous page
1/124
Next page
USER MANUAL
ENGLISH
9098960000(1)2011-04 A SCRUBTEC R 466 - R 471 - R 471C - BOOST
®
R4 19
Squeegee adjustment
If necessary, stop the machine and turn the squeegee adjusting handwheel (35) so that the rear blade touches the fl oor along 1.
all its length.
Adjustment of the detergent concentration in the solution
(For machines with Chemical Mixing System)
The system used to mix the detergent with the washing water can be activated by pressing the detergent fl ow control switch (A, Fig.
5): when one of the LEDs is on, the detergent is added to the washing water.
The average detergent concentration varies according to the illuminated sector (B), as shown in fi gure 5.1.
Press the switch (A) to change the detergent concentration to reach the desired setting, or to reset (all LEDs off).2.
NOTE
Detergent percentage setting is stored into memory, even if the machine is turned off.
NOTE
The detergent concentration is kept constant even if the washing water fl ow is changed with the switches (C) or (D).
B
A
C
D
0,4%
0,5 Oz/Gal
0,75%
1 Oz/Gal
1,5%
2 Oz/Gal
2,5%
3 Oz/Gal
Figure 5
P100439
Working with brush/pad-holder extra pressure function turned on (only for SCRUBTEC R 466 / R 471 / BOOST
®
R4)
If the fl oor proves to be particularly diffi cult to clean, it is possible to turn on the brush/pad-holder extra pressure function by 1.
pressing the switch (67).
To return to normal pressure, press the switch (67) again.2.
The switch (67) is enabled only when the deck (5 and 10) is lowered and the LED (64) of the switch (63) is on.
CAUTION!
In case of brush/pad-holder motor overload, due to foreign bodies which prevent them from rotating, or to
excessively aggressive fl oors/brushes, the safety system stops the brushes/pad-holders after about one minute
of continuous overload.
The overload is shown by the three battery warning lights (62) fl ashing simultaneously.
If the overload takes place when the extra pressure function is on, the system automatically reduces the
pressure on the brushes/pad-holders, thus turning the extra pressure function off. If the overload persists, the
brushes/pad-holders stop.
To start scrubbing again after a brush/pad-holder stop due to overload, stop the machine by turning the ignition
key (58) to “0”. Turn on the machine by turning the ignition key (58) to “I”.
9098960000(1)2011-04 A.indb 199098960000(1)2011-04 A.indb 19 07/04/2011 15:59:2107/04/2011 15:59:21
… 81 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nilfisk-ALTO SCRUBTEC R 466 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nilfisk-ALTO SCRUBTEC R 466 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info