Manual Multiplex Power Peak D7 EQ-BID - 30 8129 (page 27 of 92) (English, German, French, Italian, Spanish)

628910

Zoom out

Zoom in

1/92

Operating Instructions

Power Peak

D7 EQ-BID

Order No.

8129

13. STARTING A CHARGE / DISCHARGE PROCESS

Before the programmed process is started, the battery must be con-

nected to Output 1 or 2 with correct polarity (see chapter 5.2). Use

the appropriate charge lead from the comprehensive robbe range.

The process is actually started by pressing the "START / ENT." but-

ton: you will hear a confirmation beep. This means that the charger

is checking the battery connected to it; the screen informs you of

this.

If no battery is connected, you will see an on-screen warning of the

error, and hear a warning beep.

Note:Lithiumbatteriesmust alwaysbecharged withtheVoltage

Sensor lead connected.

Charge LiPo

Charge

Checking battery

Waiting. . .

14. SCREEN DISPLAYS DURING A PROCESS

14.1 SCREEN DISPLAYS DURING CHARGE / DISCHARGE

AND CYCLE PROCESSES

Once the process has started, the screen changes to the working

display, which shows all the important values relating to the cur-

rent process. The illustration below shows the working display for

a LiPo battery charge process. The working display is divided into

two screens.

Pressing the "START / ENT." button takes you to a display of the

voltage curve. If you are charging a Lithium battery, pressing the

"START / ENT." button a second time takes you to the Equalizer

display. Press the "START / ENT." button once more to return.

The displayed value for internal resistance is automatically calcu-

lated by the Power Peak

D7 EQ-BID.

Note:

It is possible to alter the current during a charge / discharge

process: navigate to the "CURRENT" function by pressing the

"START / ENT." button, then change the current using the "+" or

"-" buttons. The new value applies only to the current process, and

is not saved.

During a cycle process the working display also looks similar. The

screen displays "CYCLE" while the battery is being checked. The

illustration shows the upper part of the screen display during a

cycle, in this case while a battery is being charged.

When the charger is connected to the mains, i.e. the internal PSU

is in use as power supply, the "Input voltage" parameter shows a

valueof17.4V.

In addition to all the current process parameters, the screen dis-

plays the mode, the current phase and the cycle sequence. During

each phase the corresponding symbol flashes (D = Discharge, C

= Charge).

Cycle NiMH

Cycle  : D>C

Time : 00.00.46

Capacity : 38mAh

Voltage : 5.77V

Current : 1.00 A

In.Volt : 11.78V

BATT. Res : 350 mO

Charge LiPo

Time : 00.00.46

Capacity : 19 mAh

Voltage : 11.54V

Current : 1.95 A

In.Volt : 11.78V

Batt.Res : 48mO

Int. temp. : 35°C

12. CONNECTING A BATTERY

Important!!! Before connecting a battery pack, check one

last time that all the set parameters are correct! If the settings are

incorrect, the battery may be damaged, explode, or catch fire. To

avoid short-circuits between the banana plugs, always connect the

charge leads to the battery charger first, and only then to the battery.

Take care to maintain correct polarity!

Reverse the sequence when disconnecting.

Connecting the equalizer:

The black wire of the voltage sensor lead attached to the Lithium

battery must be connected to the charger at the arrow marking. The

arrow indicates the negative terminal. Take care to maintain correct

polarity!

This example is only intended as a general guide; it shows how to

connect the voltage sensor lead to the equalizer.

Note:

It is essential to connect the battery voltage sensor lead to the

charger before charging or discharging a Lithium battery. This

is a safety requirement!

Do not connect the outputs in parallel, and never connect the

positive and negative terminals together. Neglecting this war-

ning will result in damage to the charger.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Multiplex Power Peak D7 EQ-BID - 30 8129 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 9,26 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Multiplex Power Peak D7 EQ-BID - 30 8129 Manual

Product: