467082
42
Zoom out
Zoom in
Previous page
1/48
Next page
42
CAUTION:
This setting must be left unchanged all the time you are using
teacher/pupil mode. „PUPIL ON“ must remain active!
Do not disconnect the teacher/pupil lead from either transmitter
while you are using teacher/pupil mode!
5. Ending the teacher/pupil mode
Press the 3D-digi-adjustor once. The cursor moves back to the upper line and
the teacher/pupil lead can be disconnected from the transmitters.
Note:
If the two transmitters are disconnected during operation
the pupil transmitter remains in pupil mode. When switched on the transmitter
does not show the operating screen (as usual), but the PUPILs menu set to ON. If
this happens press the 3D-digi-adjustor to quit the pupil mode and select the oper-
ating display.
10. Channel-Check gives security when you switch on
The Channel-Check module is a monitor receiver which checks the channel on
which your transmitter is operating. It can be installed in the transmitter at any
time.
Every time you switch the transmitter on, the monitor receiver is automatically acti-
vated and checks whether your channel is vacant. If the channel is already in use, or
is encountering interference, the indicator lamp on the transmitter glows red, and
the RF section stays switched off. This means that you do not run the risk of operat-
ing your own model, and you will not cause interference to the other model which
could already be flying within a radius of about 300 m from your location.
10.1. Installing Channel-Check
1. Fit a receiver crystal in the Channel-Check module as shown in
the drawing alongside.
Important:
The channel numer of the crystals for the Channel-Check
module and the receiver (in the model) must be identical.
MULTIPLEX receiver crystals are fitted with a yellow plastic
sleeve and are printed with the code letter „E“ before the
channel number.
2. Open the transmitter case (Fig. I)
3. Hold the module by the narrow sides and place it carefully on the Channel-
Check socket on the main circuit board (Fig. V)
Check that the two rows of pins on the main circuit board engage correctly in
the sockets.
4. Close the transmitter case
Channel-Check
module
42


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Multiplex Cockpit MM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Multiplex Cockpit MM in the language / languages: English as an attachment in your email.

The manual is 0,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Multiplex Cockpit MM

Multiplex Cockpit MM User Manual - German - 48 pages

Multiplex Cockpit MM User Manual - French - 48 pages

Multiplex Cockpit MM User Manual - Italian - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info